Advertising on the portal

How to fix plastic panels to the wall with your own hands: detailed instructions. Wall decoration with plastic panels: independent decoration of the walls of the room with plastic panels Installation technology for pvc wall panels

Installation of PVC panels is simple and accessible to everyone. For attaching panels to concrete wall install a metal frame. Panels are attached to wooden surfaces with a stapler, nails or self-tapping screws. Depending on the use of the room, hydro-, heat-, sound insulation is attached between the wall panels and the walls.

Before installing PVC panels, the walls do not need to be specially prepared. There is no need to clean the walls from old paint, wallpaper or plaster. Cladding with wall panels is the most labor-intensive and “clean” process of finishing a room. The panels are very easy to cut in all directions. If the walls are not even, then it is easy to align them with a frame.

Wall panels are produced by manufacturers different colors and they are easy to combine with each other, creating beautiful combinations. They look good next to wallpaper, tiles. The surface of the panels can be easily cleaned with a cloth and a non-abrasive detergent.

Plastic panels are not afraid of moisture. PVC panels are widely used in bathrooms, toilets and kitchens.

Installation of PVC panels

If the room in which you are going to install plastic panels has uneven walls, then they need to be leveled by installing the crate. This will be the most time-consuming process when installing PVC panels, because. the appearance of the room will depend on the straightness of the installation of the supporting structures.

Installation of PVC panels can be carried out horizontally, vertically, as well as at any angle to a horizontal surface. At the same time, you must remember that the laths of the crate must always be strictly perpendicular to the strips of the panels. The distance between the laths of the crate should be no more than 50 cm.

When using the material for the crate, you need to consider in which rooms it is installed. In wet rooms, the crate is made of metal, in dry rooms, you can use wooden bars. Wooden beams must be used good quality, without knots, humidity not more than 18%.

1. To mount the crate, prepare a tape measure, chalk, straight rails, plumb line, mounting level. Mark on the wall with a tape measure and chalk the contours of the installation of the battens. Check with a plumb line or level the direction of the bars and fix them to the wall or ceiling with a screwdriver. The bars must be fixed on the wall perpendicular to the direction of the PVC panels. The distance between the bars should be 30-50 cm.

If the walls are not even, then the crate should be leveled with spacers made of plywood, wood or bars.

2. Choose the corner from which you will start installing the plastic panels. You can install panels from the corner to the window or to the door. You must take into account that some wall will be short and the width will not fit all the wall panels completely, and one panel will have to be cut. Such panels are best placed in less visible corners of the room.

3. In the corner from which you will begin the installation of PVC panels, install a special corner (finishing element) for internal or external corners. Fasten it to the wall or batten with a stapler or screwdriver. The comb of the panel must be located in the direction of movement.

4. Install the next panel. Push the panels firmly into each other and check along the entire length. Fasten the panel along the entire length, etc. to the next corner. In order to beautifully and evenly arrange all the corners of the room, window openings and the door, there are external and internal corners, PVC finishing elements. Use them when installing PVC panels. Press the last PVC panel firmly into the finishing element or corner.

5. The bottom of the panels is formed using any PVC floor plinth. How to mount a floor plinth you can read in the following article.

Modern technology for mounting PVC panels involves the use of metal fastening brackets. The slats are attached to the base of the walls in the manner described above, and all elements: corners, panels are fixed by snapping metal brackets.

Plastic mounting profile

Installation of PVC panels and construction tricks

1. Do not unpack PVC wall panels immediately when bringing them into the room. Soak them for at least 48 hours and at a temperature of at least +10 degrees.

2. Keep in mind that the longer the panel, the greater its elongation. Use panels with a length of no more than 3 meters, joining them using a docking profile.

3. Do not install PVC panels at temperatures below + 10 degrees.

Now hygienic and easy to install PVC panels are used in many building and renovation works. This is wall cladding. plastic panels in bathrooms, showers, kitchen areas, and finishing slopes during the installation of double-glazed windows, as well as ceiling cladding in pools. They are also often used for cladding the outer surface of walls.

The main advantage of panels is versatility. They can be mounted on almost any surface (wall or ceiling), be it brick or tile, however, their primary purpose is installation on a "wet" environment. Also, the advantages include durability, affordable cost, resistance to corrosion and ultraviolet radiation, water resistance. In addition, plastic, unlike tiles, is warm to the touch, which virtually eliminates condensation.

Care for plastic panels after correct installation practically not required. They are not difficult to wash, just do not use products with abrasive particles in the composition, as well as solvents.

In order not to be disappointed in the result, you must first slowly study the attached instructions. Each manufacturer gives its own recommendations for the installation of their products, but general principle everyone is similar:

  • At least half an hour before installing the panel, it must be brought into a room with room temperature;
  • The old coating (tiles, wallpaper), as well as dirt and dilapidated plaster, must be removed from the surface on which the sheathing or mounting will be carried out. If the tile is left, then it needs to be sanded to improve the adhesion of the adhesive to the surface;
  • Panels need to be cut with a hacksaw. You can also use a sharp construction knife or a 15 tooth saw;
  • When cutting panels, they need to be placed with the front surface on top;
  • It is necessary to remove the protective film only at the end of all work. Of course, if she was at all. This will help protect the plastic from accidental scratches, which are not uncommon when sheathing, cutting and installing;
  • It is necessary to work with a cutting tool in special glasses;
  • Glue must be applied directly to the work surface in the form of a thin and even mesh. There should be no empty lots.
  • If the wall or ceiling is damp, you can use metal racks or waterproof materials. When sheathing this kind of frame with panels, it is very important to provide for ventilation. A small gap between the panels and the wall can serve very well as ventilation;
  • If necessary, to mount sockets under the panels (telephone, power supply), special strips must be used;
  • If there are heating devices nearby, you need to check the temperature of the air heated by them. The maximum allowable temperature is 60 degrees;

Installation of plastic panels

Small nails are evenly driven into a specially designed protrusion (“lip”) on the panel. Be careful not to damage the plastic with a hammer. This method is used only when sheathing a wooden crate or wall. Fastening brackets can be a good alternative to nails, only for them you need to purchase a stapler.

When sheathing a metal crate, you need to use special screws.

Gluing pvc panels

This method is only suitable for flat, dry surfaces. The wall or ceiling must be free of dust and greasy spots. Glue must be taken special - "liquid nails". It must be emphasized that when working with panels, it is forbidden to use glue that contains solvents or cleaners.

If the shower wall is sheathed, then it is necessary to leave a small (3 mm) gap from the bottom. This is necessary so that when the pallet expands, the material does not “tear”. The seams should be filled silicone sealant. For complete watertight sealant, it is also necessary to process ceiling gaps.

Panel care

Wash plastic panels only with a soft cloth, no washcloths, hard brushes, coarse fabrics, etc. With the exception of special products, no detergent compositions also cannot be used, especially if they contain solvents or abrasive particles. In most cases, plain soapy water will suffice. After cleaning, the surface must be rinsed again with clean water.

And here is visual video panel installation:

Recently, plastic has been widely used for decoration various surfaces not only in offices, but also in residential premises due to its simplicity and ease of installation, as well as specifications and acceptable cost of the material.

There is a wide range, which is represented by a large selection of colors and sizes.

In order to sheathe walls with plastic, there is a technology for performing work that allows you to do the sheathing yourself, while saving money on calling specialists.

Main technical parameters of plastic

Plastic has the following properties, which include:

  • Attractive appearance;
  • Safety and harmlessness of the material;
  • Affordable cost;
  • simple and fast way installation;
  • Durability;
  • No need for special care;
  • moisture resistance;
  • Durability and reliability of modern plastic panels.

Thanks to the application modern technologies and wealth color solutions can achieve not only attractive appearance walls, but also to create a cozy and residential atmosphere.

Currently, manufacturers offer not only plain panels, but also the ability to create a bright ornament and even patterns.

Disadvantages of using plastic

Despite a significant number of positive aspects, this material has some disadvantages.

Which include:

  • Unhygienic: the material "does not breathe";
  • A rather poor ratio of vapor permeability and humidity;
  • A prerequisite for leveling the walls to ensure a flat and smooth surface;
  • Flammability of the material with the release of toxic and harmful substances.

Design features of plastic panels

Before you sheathe the walls with plastic, you need to understand their design and the rules for performing work.

Plastic panels are made by extrusion from polyvinyl chloride, which has a high coefficient of thermal expansion, so slight deformation is allowed during their installation.

The panels come in different lengths and widths, and the thickness, as a rule, is 5-10 mm.

A feature of the material is its moisture resistance, resistance to aggressive chemicals and additional thermal insulation due to the porous structure of the material.

Do-it-yourself installation of PVC panels.

For framing apply different types profiles.

Types of metal profiles for lathing

For relax installation work various types of metal profiles are used.

Which include:

  • Starting.

    Used as starting strip from which the installation starts. Can be used both floor and ceiling;

  • Finishing. Installed at the end of the work and helps to easily and efficiently install and secure the last strip;
  • External and internal corner profiles. Are applied to high-quality finishing of any corners;
  • Docking. The main purpose is the decorative finishing of various elements on the surface.

Necessary tools for installation

To do the job, you will need the following set of tools, which includes Circular Saw, construction stapler with staples, spatula and rubber mallet.

The saw is necessary with fine teeth to obtain an even and high-quality cut of the panels.

A stapler will be needed if a wooden frame is installed, and with the help of a mallet with a special hook, the strips are pulled up and placed in the appropriate place to create a complete canvas without seams and gaps.

The spatula is necessary for bending the finishing profile when installing the last panel at the final stage of installation.

Of the materials, you will need a pre-calculated number of plastic panels, metal profiles for the crate and self-tapping screws.

The process of installing plastic panels

At the preliminary stage, it is necessary to prepare the surface of the walls and clean them from all kinds of dirt and dust. Next, they proceed to install the frame, for which metal profiles of various types are mainly used.

Wooden beams can also be used for battens, which should be treated with special antiseptic agents in order to protect them from moisture and subsequent decay.

Set the start, finish profiles and guides.

At the next stage, the plastic strip is slightly bent and installed in the profile, and then inserted into the upper stop.

The panels are connected to each other, tightly joining, forming a seamless surface. All bands up to the last are set in the same way. The last panel is slightly cut in width, taking into account thermal expansion, and then the finishing profile is bent with a spatula and inserted into the groove until it stops.

For this procedure, you will need the help of an assistant for high-quality fastening and installation of plastic.

For decorative finishes corners and baseboards, special plastic strips and corners are used to hide small cracks and gaps. With a high-quality crate, the result is a flat and smooth surface of the walls without defects.

Their use significantly helps to facilitate further design and repair.

Watch the video:

However, it is strictly forbidden to use them for a children's room, and for a bedroom, partial use as decorative elements is possible. Full wall cladding in the kitchen further leads to the appearance of microbes in the porous structure of the material.

You can learn how to sheathe walls with plastic by carefully studying the detailed instructions and the sequence of the technological process.

With a special set of devices and minimal skills, you can beautifully sheathe the walls as a result.

How to properly fix wall panels: design and installation features

When we start a renovation, we always think about the costs first, and also try to spend as little time as possible.

And, of course, do not pollute your apartment too much. For such results, wall panels are usually excellent, which you can learn how to fix in this manual.

Necessary materials and tools

How to fix plastic panels not everyone knows.

If anyone has any idea about this process, they still face some kind of problems. In order to fix such panels, you do not have to specifically align the walls or ceiling. Bathrooms, kitchens, and the like are best suited for this process.

By the way, using plastic wall panels, you can create a luxurious room in which it will always be a pleasure to be. As for improvised means, here you also don’t have to think long, there will be just a few tools that are very easy to find at hand.

So what do we need? Below is list of tools that will be needed in the process.

If you have prepared all the listed tools, you can begin the process.

First of all, you need a tape measure. Measure the surface on which the panels will be installed so that you know immediately how much material will be spent. If the plastic panels will be mounted on the walls, they must be completely cleaned of wallpaper, dust and, if necessary, paint.

Fastening panels with battens

Wall panels can be fixed in two ways: directly on the wall or on a specially prepared crate.

In the second case, the wall must be perfectly flat if you want a high-quality result in your kitchen, or in another room in which the installation takes place.

So, in the case of a crate, you will need slats that need to be screwed to the wall at a certain distance from each other.

If the tracks are installed on the walls, the width between the slats should be approximately 40-45 cm, in the case of the ceiling 30-35 cm. Regarding the direction of fastening, the slats must be fixed perpendicularly.

The material of the wall also matters. If it is concrete or brick, it is better to fasten the slats with dowels, if the walls are wooden, ordinary self-tapping screws will do. Do not rush immediately after reading this manual to start work. You must understand how this process takes place so that there are no difficulties in the process.

Some features of fastening wall panels:

  • If you use nails when removing the structure, in the future, their reuse will not be possible due to major damage;
  • Clamps - a good option for fastening;
  • As mentioned earlier, self-tapping screws are ideal for fastening;
  • You can also think about fixing with staples using a special stapler.

If everything is ready for installation, you can begin.

You need to follow the steps in the same order as below:

If there are difficulties during the installation process, on the Internet you can find a lot of video material in which they describe in detail, and most importantly, show the whole process.

Fastening with clips

If you decide to install directly on the wall without using battens, you must be sure that the installation room is dry and the walls are perfectly level.

For example, it could be a kitchen. True, in this case, be sure that your kitchen is a really dry room. The extraction system must be adjusted.

So, in this setup you need special clips with which the panels will be attached to the rails.

The panels are made of a material that can change with temperature.

For this situation, leave a small gap between the panel and the ceiling. If you use wide enough slats, insulation or sound insulation can be placed between the wall and the plastic panels.

Don't forget that this process applies not only to the walls, but also to the ceilings of your space.

A few tips that might make your work much easier:

Now you can be sure that the fastening of plastic wall panels is an excellent choice for a quick and low-cost repair indoors, the more it is quite easy.

Dimensions of plastic panels

The finishing material appeared on the construction market relatively recently. Today it is widely used in both internal and external facing works. These panels are made of PVC - polyvinyl chloride - by the traditional extrusion method.

  1. Properties of PVC panels
  2. What are the dimensions of the plastic panels
  3. Where are plastic panels used?

Properties of PVC panels


What are the dimensions of the plastic panels

The dimensions of PVC panels in thickness are of two types: having a thickness of 5 mm, and also - 8-10 mm.

The second type of panels is considered, as a rule, the only one - because of the moldings of standard sizes that are created under the given thickness parameters.

Panel length standard:

  • for a lining with a width of 10 cm, the length is 3 meters,
  • wide panels (20-37 cm) have standard lengths of 2.6, as well as 2.7 and 3 meters.

PVC panels width:


Where are plastic panels used?

This material is great for cladding not only walls, but also the ceiling.

Proven installation method - wall decoration with plastic panels

A big advantage when installing wall panels is that there is no need to pre-level the wall surfaces. It is enough just to prepare a wooden crate (as in the case of drywall), and already fix the panels on it, which are in contact with each other like a puzzle, inserted into each other (like a laminate).

Check out how great wall panels look:

This material is great for the bathroom, being a worthy alternative to ceramic tiles.

Almost in no way inferior to tiles, the panels are still more practical: they are resistant to moisture and temperature extremes, are easily washed from almost any stains, and their installation is many times faster and easier. And their price is much lower than tiles. The most common size of panels for the bathroom is 270x25 (30) cm. Moreover, the installation of panels in the bathroom can be done in just one day.

The sizes of plastic panels for the ceiling are made from 2.5 to 4 meters in length, and the most popular sizes in width are 10, 25 and 50 cm.

The thickness of the panels on the ceiling is also different - this must be taken into account when choosing profiles for them.

In the photo below you can see how good the ceiling finished with this material looks:

Ceiling panels are identical in composition composite materials used in medical equipment and packaging food products, which indicates their environmental safety.

Ceiling panels are more flexible than metal rails and more resistant to various deformations. Composed of a large number of insulated cells, pvc plastic panel has excellent soundproofing performance.

Ceiling panels, protected from above with a layer of varnish, have excellent antiseptic properties (without attracting dust), UV resistance, and good wear resistance.

Plastic panels are an excellent material that is widely used to give a surface various decor. What is convenient, this product can be used in almost any room. There is an opportunity to create a truly unique interior. And also decorating the walls with plastic panels is a fairly simple event that does not require building experience. Although you still need to know how to do everything most correctly.

Plastic panels (lining) have another name - PVC. This is the abbreviated name of the main ingredient of the material - polyvinyl chloride. The production is quite simple and consists in the fact that the molten substance is driven through special forms. This creates a strip that is cooled and cut into right size. It turns out an excellent finishing material that can withstand almost any temperature (within residential premises).

Wall panels vary in size:

  1. There are two types of thickness - five and ten (eight) millimeters. The second indicator is combined into one, for it there are identical additional elements.
  2. The width varies, ranging from twenty to thirty-seven centimeters.
  3. Three main sizes are distinguished in height - 2.6 m; 2.7 m; 3m.

Of course, there are many more sizes. Yes, the width plastic lining reaches 120 cm. Also, any desired non-standard can be made to order.

Advantages and disadvantages

It is impossible to imagine a finishing and building material that would not have its pros and cons.


Wall panels have the following advantages:

  • Service life is practically unlimited.
  • Excellent moisture resistance. When properly connected, the seams create complete tightness.
  • The material protects the room from extraneous noise.
  • Reliability and good resistance to abrasion.
  • The cellular structure provides additional thermal insulation. When facing the walls with your own hands using the crate, there is an additional place for the insulating layer.
  • Modern technologies allow you to create various types of decor. More recently, the choice was rather limited, if not primitive.
  • Easily mounted. No complicated tools required.
  • Low price compared to other products.
  • Environmental friendliness.

Disadvantages:

  • Inability to withstand constant temperature changes. This does not apply to seasonal events.
  • When ignited, corrosive substances are released from the plastic elements.
  • Incorrect installation - reduces many positive qualities to zero.

Like any other plastic, PVC panels are “afraid” of high temperatures, and when ignited, they emit harmful substances

On a note! Currently, there are panels that are distinguished by the ability to withstand high temperatures. But they must be specially marked.

Material selection

Naturally, I want to quickly sheathe the walls with plastic panels, but they must first be selected. And this should be approached with the utmost care. After all, it depends on the right choice final result. The following rules are taken into account:

  • For bathrooms and shower rooms, as well as for all types of wet rooms - panels that are moisture resistant and do not have a relief are suitable.
  • For corridors and balconies (loggias) - it is better to choose products that are immune to mechanical damage.
  • Wall decoration with wall panels in living rooms - carried out PVC coated, which have a different relief and pattern. And also imitate natural materials.

When buying, you need to pay attention to such indicators:

  1. Appearance of the package. It must be intact, without damage. It is important to choose material from the same lot.
  2. The number of cells. The bigger, the better. You can also focus on weight. Light products are a sign of deficiency.
  3. Castle. To do this, check the two selected panels for connection - it must be reliable.
  4. Price. Too cheap products - most likely a fake.

Additionally, we suggest watching a video that tells how to select and attach wall panels.

Calculations

Wall cladding with PVC panels requires preliminary calculations. They apply to all stages of work. This helps to avoid problems in the future, as well as significantly save money and time.

Frame:

  • The location of the profiles is taken into account. It can be vertical or horizontal. It depends on the installation of plastic panels. In any case, they are always perpendicular to the racks of the crate.
  • The distance between them, which is 30 - 45 cm, is also taken into account. From everything, the required number of frame parts is calculated (+ two profiles along the edges of the wall).

Fasteners:

  • The number of dowel-nails is taken into account from a step of 35-50 cm.
  • Klyammers - there are 20-25 pieces per square meter.

Panels:

  • Measures the size of the wall and the selected panel. One indicator is divided by another, and the required amount is obtained.
  • The material in the form of a tile is calculated based on square meters.

This group includes all other parts and moldings. For the calculation, measure the entire perimeter of the room. Take into account the number of external and internal corners.


On a note! All calculations are made with a margin of 10%. Such a reserve is due to the fact that various damage to products or other unforeseen circumstances are possible. Door and window openings are also taken into account.

Frame methods of wall decoration

Do-it-yourself wall cladding with plastic panels can be done different ways. But, before choosing the most suitable one, you should prepare the necessary tool and purchase material.

For work you will need:

  • Perforator and set of drills.
  • Drill and drills.
  • Screwdriver or screwdriver set.
  • Sealant gun.
  • Level and construction knife.
  • Hardware and other consumables.
  • stapler.
  • Hammer.
  • Necessary material and additional elements.

Training

After calculations, it is necessary to prepare the surface for facing with plastic panels. This is done based on the chosen method.

  1. Whatever options are made necessary calculations and take all sizes.
  2. Racks for the frame are marked and cut - they are numbered in order.
  3. Everything superfluous is removed from the walls. If there are damage in the form of cracks, then they are puttied.
  4. The surface is covered with an antiseptic. It is better to use two in one - a primer with the addition of substances against fungus and mold.
  5. If it is assumed that the surface will be glued with PVC, then it is pre-leveled.
  6. The use of wooden elements should begin with their impregnation. This is done with antifungal compounds.

On a note! The primer is applied in two layers. The first strengthens the surface, the second fixes the result. Wait for them to dry completely, it takes at least 6-12 hours.

Lathing and its installation

The frame is made when there are large surface imperfections, and too much effort will have to be made to correct them. Finishing with PVC panels on the crate - helps to hide all the irregularities of the walls. This method has two more noticeable advantages: it is possible to lay additional elements of insulation and hide communications. To achieve the desired result, use different materials, which do not differ much in the way they are mounted.

Creating a wooden frame


  1. For this, wooden bars are used, which have a cross section of 40 * 40 (40 * 30) mm. Fastening is done on dowels to concrete bases and on self-tapping screws to wooden ones.
  2. When paneling a room vertically, the installation starts from the edges. Namely, two initial guides are screwed. Next, calculate the same distance and put the rest of the rack.
  3. Cross bars are attached between them.
  4. If you want to achieve greater rigidity, then put additional vertical slats.
  5. It should be borne in mind that each part is checked by level. If leveling is required, then use linings from the remnants of the timber. They are pre-attached to the wall.
  6. For a greater effect, the joints of the racks and crossbars are coated with silicone sealant.

Advice! Wood sheathing is best used for dry rooms with a moderate indoor climate.

Lathing from metal profiles


This option literally repeats the installation of gypsum boards. After such work, a lot of scraps remain, which, if desired, can be used for wall cladding with PVC panels.

This method is not used as often as the others. The fact is that the cost of such a frame is very high.

  1. First fix the top and bottom rails. This is done respectively to the floor and ceiling. They are first aligned with each other.
  2. Now comes the turn of the vertical guides. They are aligned with each other and fixed on the wall. This is due to the U-shaped brackets.
  3. Horizontal crossbars are fixed with equal spacing. In general, this is not necessary, the metal profile already creates sufficient rigidity.

When you have to bypass doorways, the vertical racks are pre-strengthened with a wooden bar.

Use of plastic profiles


Plastic profiles for PVC installations lining

Finishing with plastic panels using this method is one of the most modern. It is in many ways superior to all the above types, but its popularity is not yet so high. This is due to both cost and increased surface requirements. But the plastic crate is not afraid of exposure to moisture and mold.

  • Installation of such a design on the wall occurs in a very short time. This is done with dowels. Often, such guides already have reaming, which greatly facilitates the process.
  • They are fixed with a small step of thirty centimeters. This is done in order to give the greatest rigidity.
  • In principle, when working with such elements, nothing more is required. But it is very important to observe thorough perpendicularity. This is the only way to ensure the correct cladding with PVC panels.

1 - fixing plastic profiles to the wall; 2 - installation of a corner element; 3 - installation of plastic panels, fastening to profiles using clamps; 4 - installation of the upper plinth.

On a note! Plastic profiles are great for internal walls bath complexes.

Installation of plastic panels

When the frame is finally ready and checked by level, the main process begins. It gives a complete understanding of how to sheathe walls with plastic panels.


Wall cladding with panels using a plastic profile is much faster. It already has grooves in which the clamps are fixed. They securely fix each element. And also make it possible to disassemble the entire structure without damage.

Glue mounting

If the walls are sufficiently even, then work can be carried out without using the frame. Liquid nails are used as fasteners.

When choosing a glue, you need to pay attention to its composition. It must not contain solvent. Otherwise, the lining will simply collapse.

Training

When do-it-yourself wall decoration with PVC panels occurs according to the adhesive version, then the preparation of the walls is most carefully approached. Here it will not be enough just to remove the excess - it is necessary to completely clean the surface. And in some cases create new layer putties. And be sure to apply an antibacterial primer.

On a note! Currently, there are types of putty that include antifungal agents.

pasting

The whole process must occur quickly enough, and all movements must be verified. The fact is that it will be almost impossible to correct the shortcomings. That is why this method requires some skills.


So:

  • The primer coat should dry well. After all, plastic finishing cannot be carried out on a wet wall. Nothing will hold.
  • Glue is prepared according to the instructions. When canned formulations are used, they are thoroughly mixed beforehand.
  • For work, use a special gun, roller or brush. The area of ​​application of the adhesive composition should not exceed two structural elements.
  • The corner element is installed first. A lining is inserted behind it and pressed against the wall. You need to do this without any extra effort, and even more so - point pressing. It is very easy to damage the cellular structure of the material.
  • So, sequentially, they cover the entire area with plastic with their own hands. At the end, the finishing moldings are fixed.
  • Now comes the turn of decorative elements.

Finishing with wall panels can also occur on adhesive tape. This method is not yet so sealed, so you should not trust it. And the point is precisely the tape used. Its quality does not always meet the required parameters.

Of course, each master can offer his own variations, which certainly deserve respect. But, when real experience is negligible or completely absent, then it is better to follow the proven path, even if it takes a little longer. After the first success, it will become extremely clear: how to sheathe the walls with plastic.

PVC panels are a popular finishing material that is durable, practical and affordable. Such coatings can be used both for wall cladding and for decorating the ceiling. Plastic panels are installed quite simply and quickly. It is quite possible to cope with such work on your own. Today we will talk in more detail about how to fix PVC panels to the walls.

Advantages and disadvantages

Plastic panels are in demand and common wall covering. They can be found in many stores specializing in the sale of finishing materials.

Wide sheets and plastic lining are in great demand because they have many positive qualities.

  • First of all, it should be noted the durability of such finishing materials. In our climate, their service life can be more than 20 years.
  • Such materials are wear resistant. They are not afraid of dampness and moisture. In addition, they are not subject to decay, like, for example, natural wood.
  • Plastic panels do not require complex and regular maintenance. Dust and dirt do not accumulate on their surface. If the finish is dirty, then it can be cleaned with a regular damp cloth.
  • PVC panels have soundproofing properties, so they are perfect for wall cladding.

  • Using plastic panels, you can divide the space into functional areas.
  • Plastic panels are lightweight materials, which makes them easy to work with. All processes can be handled without the involvement of assistants.
  • Plastic is a very malleable material - it easily lends itself to various types processing. Therefore, in stores you can find PVC panels that have a variety of colors, textures, prints and ornaments.

  • These finishing materials can be used in the interiors of the most different styles. The only exception can be only pretentious and pompous ensembles, in which only expensive and natural elements should be present.
  • You can install plastic sheets both in a city apartment and in a private house.
  • Behind the panels you can hide various communications, for example, electrical wiring.
  • It is quite possible to install PVC panels on walls with your own hands, since this process is not complicated and inaccessible. You don't need expensive tools to do this.

Certainly, PVC wall panels are not ideal finishing materials. They also have their own weaknesses.

Knowing all the advantages and disadvantages of PVC panels, it will be easier to work with them. You can avoid many mistakes during the installation process.

Criterias of choice

PVC sheets produced by various manufacturers have different properties and performance characteristics. At the time of buying suitable material it is necessary to pay attention to its quality - this is the main criterion on which to rely.

  • there are damages on their stiffeners (even barely noticeable) or they are completely deformed;
  • stiffeners protrude too much;
  • if the lines of the pattern on the front half are poorly expressed, and there is also blurring of the edges;

  • scratches and other minor damage are visible on the surface of the panels;
  • lamellas from one set differ from each other in hue and brightness (such a finish will look inharmonious and ridiculous on the walls);
  • panels from one set have different sizes (in this case, the finishing installation technology will be noticeably complicated, since different-sized elements will not be fixed qualitatively).

Pay attention to the decorative layer of the panels. Any drawings, prints and paints should not be blurry or too dull. These features may indicate the low quality of the material. Such coatings will quickly lose their original appearance.

Currently, PVC panels of Chinese and European production are found in stores. European products are considered to be of better quality.

When choosing a suitable material, it is necessary to pay attention to its density. It depends on this parameter how durable and wear-resistant the panel is. This indicator is affected by the number of rigid edges that are located in the inner part of the sheets.

The optimal indicators are:

  • thickness of the front side - 2-1.5 mm;
  • the number of stiffeners - 20-30;
  • the total weight of the part is 2-1.7 kg / m2.

To make sure the reliability and strength of the material, you should press on it with your finger. The front side of the panel should bend slightly under its pressure, and then quickly return to its original state. If the lamella is strongly deformed, then this indicates that it contains a large amount of chalk - such materials do not last long and are very fragile.

Preparatory stage

If you decide to install PVC panels yourself, then you should adhere to a specific work plan. If at each stage you do everything correctly, the result will not disappoint you.

First you need to prepare the wall base for future plastic cladding. This work is especially important if you plan to attach PVC panels in a frameless way.

Work algorithm.

  • First you need to remove the old finish coatings and any elements that may fall off the wall.
  • It is also necessary to get rid of all the defects of the floors. If there are noticeable potholes or cracks on their surface, then they should be repaired with a suitable solution.
  • Too prominent areas need to be cut off.
  • When the wall is leveled, and all the shortcomings are eliminated, it must be treated with a high-quality primer with antibacterial components. Such coatings are necessary so that the base is protected from the formation of mold or fungus.

Only after all the work done on the preparation of the walls, you can proceed to the design of the crate (if you use the frame method of installing the material).

Tools and accessories

For the installation of PVC panels, it is necessary to properly prepare and stock up on all necessary tools and accessories.

You will need these tools:

  • tape measure with a pencil or marker (indelible) to mark;
  • a hacksaw with small teeth for cutting sheet panels;
  • building level and plumb line, so as not to encounter distortions and irregularities;
  • triangle;
  • plastic profile, slats for decorating the corners of the structure;

  • self-tapping screws, dowel-nails, kleimers for fixing various elements on the base;
  • screwdriver and perforator;
  • sealing composition;
  • glue;
  • antiseptic.

Also in the process you will need special accessories:

  • external and internal corners;
  • docking profiles;
  • starting profiles;
  • F-shaped profiles;
  • ceiling and floor plinths.

All tools and accessories must be of high quality and reliable.

Payment

It is recommended to proceed to finishing work only after all necessary calculations have been made. This stage is needed to find out the exact number of PVC panels that you will need for wall cladding. Thanks to accurate calculations, you can avoid unnecessary overpayments due to the purchase of material with a large margin.

Fixing PVC sheets involves their horizontal or vertical arrangement. In this case, the choice remains only with the owners.

  • first you need to measure the entire room (that is, find out the length along the perimeter);
  • then you should subtract the width of the window and doorways;
  • now the remainder must be divided by the width of one PVC panel.

As a result of such simple calculations, you will get the number of panels needed to finish the room. It is recommended to add a couple of additional units to the resulting value. This is necessary so that you have a spare in case of damage to some parts.

As for the calculation of the amount of material horizontally, it is carried out as follows:

  • first you need to measure the area of ​​\u200b\u200bthe room;
  • then from it should be subtracted the area of ​​the door and window openings;
  • the resulting number must be divided by the area of ​​\u200b\u200bone panel from the kit.

Add 10% to the final figure - this will be a reserve. It should be borne in mind that when laying out horizontally, plastic panels will have to be cut, so you will have leftovers in the form of PVC scraps.

Mounting methods

Installation of plastic panels can not be called too complicated. According to experts, it is quite possible to cope with such work alone, since PVC sheets do not have much weight.

There are two main methods for installing such facing materials. The first one is the frame. Choosing a similar installation option, you should be ready to make a reliable and high-quality crate, to which plastic sheets will be attached. The second installation method is frameless. With this option, you do not have to make a separate frame, but you will need to carefully prepare the wall base for the future application of finishing materials. Otherwise, PVC panels will not hold firmly and securely to the ceiling.

It is worth considering in more detail how PVC sheets are installed in both cases.

On the frame

When you have completed the preparation of the rough floor, you can begin to prepare a high-quality frame. It can be made of metal or wood. Both options are quite reliable and durable. However, if you want to build a wooden structure, then it must be additionally treated with antiseptic agents to protect it from rotting and drying out.

Guide rails must be installed perpendicular to the PVC panels. Simply put, if you are going to mount the sheets horizontally, then the crate should be vertical and vice versa.

The frame slats should be mounted at a distance of 30 cm - this value is optimal in this case. These parts must be fixed at the beginning and end of the wall, as well as around door and window openings.

It is recommended to fasten the frame structure for plastic panels to the bases with dowels. IN concrete floor insert fasteners 6x40 mm (this is necessary so that on the other hand concrete base a piece did not fall off), but in brick - 6x60 mm. Fasteners are recommended to be installed, adhering to an indent of 50-60 cm.

The crate must be set in the same plane- so the plastic sheathing will turn out to be even and neat. To achieve this effect, you can use small wooden linings or ordinary plywood pieces and install them under the frame planks. Do not forget that these elements also need to be treated with antiseptics.

It is also permissible to use special perforated hangers, which are usually used for plasterboard ceiling structures. Such elements are necessary for placing metal profiles in the same plane, but they can also be used in the case of wood frames.

If you plan to use for the construction of the frame plastic profiles, then you should consider one important nuance: these elements should only be perpendicular to the PVC panels. The slightest deviation can lead to many problems, for example, the clamps may not close and will not perform their main function. To avoid such errors, it is worth constantly checking the verticals and horizontals.

Also, experts advise installing wooden frame elements around the perimeter of the room. the same thickness as the PVC profiles, since the launch panels will be attached to these bases.

Further, at the level of the floor and ceiling, a starting or ceiling plinth should be used. The starting element is a narrow plastic strip. Ceiling plinth - a shaped part that has a special cutout.

Laying PVC profiles should begin in one of the corners(top or bottom). Finishing should be fastened to the frame slats. Fasteners are selected depending on the material that you used to construct the crate. The result is a design that resembles a frame. It is into it that the PVC panels will be inserted further.

Next, you need to cut the starting lamella in accordance with the length and height of the wall. To cut off excess pieces, you should use a hacksaw or a special saw for metal. When cutting the panel, do not press on it with your foot or hand too hard - you will push it or break it. In order for the first part to fit correctly in the right place, it is necessary to measure its length again. Subtract 4-5 cm from it and cut off.

At the starting strip, it is necessary to cut off the protruding spike. After that, with the cut side, this part must be inserted into corner profile by tucking the edges into the top and bottom profiles. It is worth tapping lightly with your palm to drive the bar as deep as possible.

Be sure to apply a level to the edge installed element to check its evenness. If the part stands correctly, then you can safely fix it to each lath of the crate.

When you install the launch pad, you should cut the second one, dock it with the first one and fix it. Further actions are very simple and uniform. Problems often arise only with the installation of the last lamella on the floor. Most often, this part has to be cut in width, after which you need to try to fill it at the same time in the groove and in the profile (starting or corner). This is not always possible to do neatly, because the plastic is easily wrinkled. To avoid such a problem, you should not install a second corner profile. In this case, this part is put on a fitted finish panel. Then these assembled elements are joined to the previous lamella. The profile is fixed only after these actions.

Further cladding of floors with PVC panels occurs in exactly the same way.

According to experienced finishers, the frame method of mounting plastic panels is reliable, but more complicated than frameless.

frameless

In cases where the floors are flat, plastered or sheathed with drywall, they do not require the installation of a crate for plastic finishing. In this case, it will only take away the free space in the room. On such bases, PVC panels are attached using silicone, liquid nails or mounting foam.

However, in this case, the launch panels will still have to be fixed to the walls with dowels.

After that, the following is applied to the back half of the sheets:

  • foam (it is better to lay it on PVC sheets in a zigzag pattern);
  • silicone (it is recommended to apply it on the panels in small portions at intervals of 10-15 cm).

Then the bar is inserted into the profiles and pressed tightly. After that, it is fixed with fasteners. Further, the installation of plastic panels should be continued according to the same principle.

The main advantage of this installation method is that it takes a minimum of free time. However, you can only contact him if the walls in your home are ideally flat surface without major flaws. It should be borne in mind that in the future it will hardly be possible to remove such a finish without damaging the plastic.

Plastic wall cladding is not the best hard work. The main thing is to follow the instructions provided and use quality materials / tools.

If you decide to do such finishing work with your own hands, you should take into account some recommendations from experts.

  • It is not recommended to combine PVC panels with more expensive materials. For example, the union of luxurious marble and PVC will look ridiculous and disharmonious.
  • According to experienced craftsmen, hot glue cannot be used for PVC.
  • To make a competent installation of the panels around the sockets, you must first make all the necessary holes for them in the material. Before doing this, be sure to turn off the electricity.

  • If you designed a wooden crate in the bathroom or in the kitchen, then a couple more millimeters must be added to the resulting indentation, since the wood is subject to deformation under the influence of dampness, moisture and temperature changes.
  • PVC panels are a popular and sought-after material, but they are not recommended to be installed in the bedroom (both for children and adults). For such rooms, it is better to choose more "breathable" materials.
  • It is not recommended to sheathe walls with PVC panels immediately after purchase. They should rest in a dry and warm room for at least 2 hours.
  • Wall decoration should be started only after the floor and ceiling are ready.
  • The advantages of PVC panels include their ability to hide various communications. However, these elements must still be available to hosts. To do this, use removable inserts.

  • If you use liquid nails to fasten PVC sheets, then you should not pull with the removal of their influxes - these compounds dry out very quickly.
  • Wall finishing materials should not have different openings at the joints. You need to follow this when choosing plastic panels.
  • At each stage of laying PVC panels, it is necessary to check the evenness of the structure using a level. This device will help to avoid bevels and curvature of the finish.
  • Experts recommend purchasing high-quality PVC panels. Do not look for too cheap coatings - such materials are already available. Ask the seller for quality certificates of paintings. Study them carefully. The composition of such finishing materials should not contain toxic compounds.

Design Options

PVC panels look organic in many settings. Designers do not recommend only combining such coatings in one ensemble with very expensive and pompous coatings (for example, natural stone). Against the background of such finishing materials, PVC sheets may seem too modest and even “poor”.

Plastic panels are able to enliven the interior of the hallway, corridor, living room, bathroom and kitchen. The main thing is to choose coatings of a suitable color and texture.

On the small kitchen in the loft style, the dining area can be distinguished by PVC panels imitating dark red brickwork. Against such a background, a laconic white table and metal chairs with dark wooden backs and armrests will look harmonious. The dining area will look complete if you hang a large dark clock above the table.

PVC panels can be used to design an apron in the kitchen. For example, in a room with burgundy walls, a white floor and the same white set, an apron trimmed with a wide plastic sheet depicting coffee beans will look spectacular.

In the hallway, PVC panels are used most often. In such rooms, coatings imitating brick and stone look especially attractive. They are usually adjacent to ordinary wallpaper neutral colors. For example, canvases under a light brown stone will look harmonious in tandem with yellow wallpaper and a wooden front door.

Also, in the conditions of a hallway or a corridor, PVC panels with a silkscreen effect look good. Against the background of such light canvases, both entrance and interior doors dark shades. Such coatings look attractive, adjacent to wooden furniture and decor items.

With the help of PVC panels, you can revive the interior of the living room. In such environments, 3D coatings with embossed surfaces look especially original and stylish. For example, spectacular textured black canvases can be used to decorate an accent wall with a TV, and place a dark chocolate woven sofa opposite it. So that the ensemble does not seem too dark and oppressive, a light laminate should be placed on the floor.

The article will discuss how to fix PVC panels to the wall and to the ceiling base: possible options for fixing the material on the surface will be studied in detail, the main step by step technologies, the nuances of the correct use of the material and the creation of design in the premises with the help of it. Visual examples of the design of the bathroom, kitchen, balcony and other premises will also be provided.

Fixing PVC panels to the wall can be done using adhesive, self-tapping screws or kleimers

Panels made of polyvinyl chloride are practical and durable. For this reason, they are widely used to decorate the surfaces of walls and ceilings in the house. Due to the wide variety of shapes, shades and textures, interiors based on this material can be stylish and beautiful.

Useful advice! Use PVC panels for bathroom renovation. This material is hygienic and not at all afraid of water, so it can be used in those rooms where other finishes are not suitable. On the Internet, there are not only photos of finishing the bathroom with PVC panels, but also design options using this material in the kitchen, in the toilet, on the balcony or loggia, in the sauna.


Material advantages:

  • resistance to moisture;
  • convenient installation system, which even a beginner can handle;
  • long service life;
  • fire safety;
  • resistance to mold, fungi and other microorganisms;
  • hygiene;
  • ease of care and cleaning;
  • affordable cost.

On the net, you can stumble upon a photo of PVC panels for the kitchen; instead of a tile, this material looks no less beautiful, while its cost is much lower than that of a tile.

The disadvantages of PVC panels include a low level of impact strength. Therefore, you should carefully control the process of transporting material from the place of purchase to the work area. When installing PVC wall panels with your own hands, you should also be careful not to damage them.


Before you start installing PVC panels in the bathroom or in any other room, you should prepare the tools and materials necessary to complete finishing works. They should always be at hand.

To repair the premises with PVC panels, you will need:

  • tape measure and pencil (for marking);
  • hacksaws with fine teeth (for cutting material);
  • building level;
  • square;
  • PVC panels;
  • plastic profile for PVC panels or rails;
  • a set of fixing elements (self-tapping screws, dowel-nails, kleimers);
  • perforator and screwdriver;
  • antiseptic solution and sealant;
  • ceiling plinths.


At the same stage, the selection and purchase of material is carried out. There are panels on the market with different type coating, which can be glossy or matte. In addition, manufacturers use various technologies applying patterns and drawings.

Strength characteristics depend on the wall thickness of the panel, as well as on the number of stiffeners that are located inside.

Useful advice! To test the material for strength, gently press the surface of the plastic with your finger. If the panel is bent, it means that it has a low strength index and short service life.

Features of the choice of material for wall cladding with PVC panels

PVC panels from different manufacturers have different characteristics. Be sure to pay attention to the quality of the material.

To purchase a quality panel, avoid buying material if:

  • stiffeners are damaged or deformed;


  • the lines of the pattern on the front of the panel are not clear, blurred, or the edge line is smeared;
  • lamellas differ from each other in shade;
  • the surface is covered with scratches;
  • the dimensional parameters of the lamellas do not match (in this case, the technology of attaching PVC panels to the ceiling or wall can be not only complicated, but also impossible, since the elements will not be tightly fixed).

Characteristics of the average European and Chinese panels (comparison table):

Criterion European lamella Chinese lamella
Front side thickness, mm 2 1,5
Number of stiffeners, pcs. 29 20
External characteristics of stiffeners smooth, no distortion smooth, there are slight deformation changes
Lamella weight, kg/m² 2 1,7
External characteristics of the lamella Even coverage, stiffeners do not protrude Smooth coating, translucent voids between the stiffeners, there are slight deformation changes
The quality of the raw material base From a light touch, the lamella bends a little and returns to its original state again, the presence of chalk in the composition is minimal From a slight pressure on the surface with a finger, the lamella undergoes deformation changes, which indicates a high content of chalk in the composition.

How to fix a PVC panel to the ceiling and wall: preliminary calculations

Before fixing the PVC panel, it is necessary to make preliminary calculations of the material for finishing the wall.

Useful advice! Be sure to calculate the amount of material. This will allow you to avoid overpayments or additional purchases of panels if there are not enough of them. By doing preliminary calculations, you save both time and money.

When installing PVC wall panels, the lamellas can be positioned horizontally and vertically. It depends on your desire. Material calculation for vertical mounting is carried out as follows:

  1. Measurements of the room are carried out (the length of the room along the perimeter).
  2. From the value obtained, the width of window and door openings is subtracted.
  3. The remainder is divided by the width of one lamella.


As a result, you get the required number of panels for finishing the room. Be sure to add a few extra lamellas in case you accidentally damage one of the elements during installation.

For horizontal finishing, a slightly different calculation scheme is used:

  1. measured total area premises.
  2. Subtract the area of ​​window and door openings.
  3. The resulting value is divided by the area of ​​one lamella.

In this case, at least 10% of the panels in reserve must be added to the amount received. This point is due to the fact that when finishing the ceiling horizontally with PVC panels, as well as when working with walls, the master is faced with the need to cut the material. The result is more construction waste.

Calculation of consumables for battens under PVC panels

If you plan to install PVC wall panels with your own hands on top of the crate base, you should perform additional calculations of the quantity Supplies for this design. As building material metal profile elements or wood slats can be used for the crate.


First you need to measure the height of the walls in the room. Then this indicator is divided by the step of placing the rails in the crate. The result of these calculations must be multiplied by the perimeter of the room. You will receive the length of profiles or rails in running meters.

Note! As a rule, wooden or metal elements are located in 50 cm increments from each other.

To calculate, measure the height of the corners in the room and multiply this figure by their number. As a result, you will get the total footage of the profile elements of the angular type. The perimeter of the door and window openings in the room is added to this value.

Using PVC panels: how to attach plastic slats to the wall in the bathroom

Numerous photos of PVC panels in the bathroom, which can be found while browsing websites and home repair magazines, indicate that this type of material is quite popular among consumers.


Do-it-yourself bathroom decoration with PVC panels can be done in three different ways:

  • with the use of adhesive composition;
  • using self-tapping screws;
  • using clamps.

The use of adhesive composition will be effective if you have to deal with perfectly flat and smooth surfaces.

Types of glue for PVC panels in the bathroom:

  • specialized adhesive composition for PVC lamellas;
  • universal composition "Moment-installation";
  • liquid Nails.


Installing lamellas with glue greatly simplifies and reduces the cost repair work in the bathroom, as there is no need for the construction of a crate structure.

The adhesive method of fixation also has disadvantages. If the finish is damaged, the damaged lamella cannot be replaced with another one. Moreover, subsequent repairs will be complicated by the procedure for dismantling the old coating, which is difficult to remove from the wall.

Fixing with self-tapping screws is more convenient and reliable. For work, you will definitely need an auxiliary tool in the form of a screwdriver. Otherwise, the repair will be significantly delayed.

Note! Before fixing the PVC panel in the bathroom with self-tapping screws, there is no need to level the surface.


The disadvantages of this method include the need to build a frame base in the form of a crate made of wood. This entails additional costs of time and money.

Kleimers provide quick and reliable fixation of lamellas on the wall surface. In this case, the crate structure must be metal.

Finishing the bathroom with PVC panels: interesting ideas, photos

Plastic trim opens wide opportunities regarding the design of the bathroom - photos of PVC panels in the design of this room look stylish and impressive. Variety of colors and external characteristics material allows you to equip the room in different styles.


Eco-friendly interiors are very popular today. Of course, plastic does not belong to the category of environmentally friendly and natural materials, but in the photo of the bathroom, PVC panels with wood texture create an excellent imitation of ethno style. Mounting pvc panels in the bathroom on the walls it is ideally combined with the ceiling decoration made with the help of slats.

In the photo of bathrooms, PVC panels imitating tiled flooring look so natural that they are almost indistinguishable from real tiles. In this case, you achieve significant savings in terms of material purchase costs, since plastic lamellas are much cheaper than ceramic tile. When repairing a bathroom with pvc panels for tiles, you have the opportunity to decorate the room in a neoclassical style by adding friezes, columns, borders to it, or classic version finishes.

Useful advice! It is not recommended in the design of the bathroom, as well as in the decoration of the toilet, to combine with finishing materials from the expensive segment. The neighborhood of PVC with marble looks not only tasteless, but the presentability of natural stone is also completely lost.


In the photo of finishing toilets with PVC panels, light colors look very advantageous. Thanks to this, a small bathroom can add additional volume. TO modern options the design of bathrooms includes the use of products with photo printing or the installation of mosaics.

For finishing bathrooms, it is recommended to use plastic lamellas with a slightly pronounced textured surface. The fact is that volumetric textures can be an excellent basis for the formation of mold and fungal spores. If you buy material with large embossed grooves on the surface, it will be difficult to care for the finish later.

There are also advantages in how PVC panels are attached to the walls in the bathroom:

  • saving money - the average prices for panels with standard dimensional parameters are in the range of 200-300 rubles / piece. The range of market value of the material covers prices from 100 to 500 rubles per piece. This indicator depends on the quality of products and design;


  • hygiene and safety - the surface of the lamellas does not absorb unpleasant odors, easy to clean with a sponge and soapy water;
  • high level of moisture resistance. For this reason, the material is suitable for rooms with high level humidity. This property allows you to finish the loggia with PVC panels, as well as the balcony, corridor and even the kitchen;
  • simplicity of the installation system - for this it is enough to have the skills to use a construction stapler and a screwdriver;
  • practicality - in the photo of bathroom decoration with PVC panels, communication systems are not visible. The material is used for lining communication boxes, where all pipes, valves and other elements are placed.

Note! Plastic panels have excellent performance characteristics: low flammability, thermal and sound insulation.

How to glue PVC panels on walls without battens

Before gluing decorative panel PVC on the wall surface, it is necessary to prepare the base. This technology requires thorough cleaning of the walls with their subsequent alignment. Errors in the choice of glue are also unacceptable.

Surface preparation involves:

  • complete removal of the old coating;
  • elimination of gaps;
  • surface leveling.

Allowed size differences within 5 mm. If the pits and bumps are deeper, over time the plastic will peel off or deform. Grease, dust, dirt may be present on the surface of the walls. These particles interfere with the normal adhesion of the adhesive. Therefore, it is desirable to wash off the whitewash from the surface of the walls, clean the fat with the help of an effective detergent and apply primer.

List of universal adhesives:

  • Emfikol 34012A;
  • Kleiberite 636;
  • Crystal moment.


When installing PVC panels, non-expanding polyurethane foam or liquid nails can be used.

These compositions can be used for mounting PVC panels with your own hands, but experts recommend using specialized glue for plastic.

Signs of a quality composition:

  • transparency after drying and the formation of a film layer;
  • resistance to the effects of sudden temperature changes, moisture and frost (for this reason, photos of finishing balconies with PVC panels are so common on the Internet);
  • fast grasp;
  • reliable and long-term fixation.

Note! It is strictly forbidden to use hot glue to fix the plastic.

A non-expanding polyurethane foam sealer or liquid nails can be used. These materials are plastic and firmly fix the panels on the wall.


Decorative PVC mosaic panels: how to glue, video instruction

To learn how to glue PVC mosaic sheet panel, use step by step instructions, which is also applicable to conventional lamellas.

Step by step procedure:

  1. Cleaning the back of the panel with a damp cloth.
  2. Drying the panel (before gluing the PVC mosaic panels, the surface of the material must be completely dry - only then can the adhesive be applied).
  3. Application of the adhesive composition on the back side by the dot method in increments of 25-35 cm.
  4. Mounting the panel to the wall.

If you use liquid nails in your work, the panel will then need to be lightly tapped and torn off the surface again. For better adhesion, the glue requires weathering for 5-7 minutes. Then you need to re-secure the lamella in place.


The frameless method does not require the formation of external and internal corners for PVC panels. Such a procedure would be inappropriate in this case. Enough of the usual cladding with plastic corners that do not have grooves for mounting lamellas. To fix the corners, you can use transparent silicone. The size of such elements varies in the range from 2 cm to 5 cm.

Useful advice! To install the trim around the sockets, you must first cut holes for them in the appropriate place on the panel. Be sure to turn off the electricity while working.

Use the video below for a more detailed study of the procedure for installing PVC wall panels with your own hands.

Last but not least, floor and ceiling plinths for PVC panels. Use self-tapping screws for this. The joint zones between the lamellas must be filled with silicone or.

Photo of kitchen aprons made of PVC panels and spacer mounting technology

Most often, expanded clay or tile is used for finishing kitchens. However, the installation of these materials requires special knowledge and skills, so more and more often you can see PVC panels in the photo. Due to the special design of the lamellas, the assembly of the wall in the apron area is carried out with minimal gaps.

The technology of fixing the lamellas into the spacer does not involve the use of fasteners, adhesives or battens. This method is used exclusively in small kitchens, where the work area can be covered with a single sheet panel.

  1. Install the panel with the bottom edge on the countertop and cut the material according to the size of the apron.
  2. Mount the slats in the apron area so that the upper edge of the material goes under the wall cabinet and is firmly pressed against it. To improve fixation, you can use fasteners in the form of hidden brackets.
  3. The lower end is fixed with a plinth. This part is fixed to the countertop and it is better if it is massive and durable.

Note! The advantage of this technology is that if it is necessary to repair the premises, the lamella can be easily removed. The material is not damaged and can be reused.


Instructions for installing PVC panels on walls over the crate frame

Before sheathing the wall with PVC panels, the surface should be cleaned. There is no need for serious alignment, but if it is planned to finish the bathroom, kitchen or other wet room, walls are recommended to be waterproofed and coated with an antiseptic.

To form the crate structure, wood bars 2x2 cm in size can be used. They are much cheaper than metal elements. However, it is not recommended to use a wooden crate for rooms with a high level of humidity. Before using wood, it must be thoroughly dried so that the moisture content of the material reaches the permissible norm - 12-15%. Do not forget to pre-treat the bars with an antiseptic.

To arrange a metal frame, you will need a UD profile element (contour part) and CD (guides).


Regardless of whether you make ceilings from PVC panels with your own hands or sheathe walls, the construction of the crate structure should begin with markings. If you are working with walls, you first need to determine the lower level, taking into account the further installation of the plinth. As a guide, you need to take the most protruding point of the wall. It is she who will determine the indentation of the crate.

Useful advice! For a wooden crate, another 2-3 mm should be added to the resulting indent, since the wood is subject to deformation changes under the influence of temperature and moisture.

After that, the line of the upper level (with a reference to the ceiling) and side levels is determined. To control the upper and lower zones, it is recommended to use a building level, for side elements - a plumb line.

How to fix a PVC wall panel: working with a frame and cladding

Fixing the elements of the crate is carried out using direct suspensions. Screws are located in increments of 20-25 cm ( wooden frame) or 15-25 cm ( metal carcass). The installation of bars or metal profiles is carried out first along the edge, then inside the structure. This will ensure that the trim is securely fixed at the edges.


When installing internal profiles, it is worth considering the type of panel installation you have chosen - horizontal or vertical. The slats will subsequently have to be attached perpendicular to the guides fixed with screws.

Scheme of mounting panels on the crate:

  1. Installation of external and internal moldings.
  2. Installation of the first panel and fixing with a clamp (lamella spike must enter the profile).
  3. Mounting the second panel in the groove of the previously installed lamella and fixing in the same way.
  4. Installation of material to the end of the wall.
  5. Open the last panel, taking into account the fact that the finishing material must be installed all the way to the corner area. In this case, a gap of 2-3 mm should form between the spike of the last element and the groove of the previous lamella. The cut side should be placed in the profile and the final element should be inserted into place.

Use for a more detailed look at the installation of PVC wall panels with your own hands video - an overview of this procedure.

Note! If you want to hide, the fixation of the first panel must be carried out strictly in the corner zone, and the installation of all subsequent elements must be carried out closely. On one of the corner elements, you need to remove the spike so that a groove appears on the end. Hook brackets will be pushed here, which are installed on the second profile element. The next lamella in the corner area will be placed in the starting profile element.

Formation of suspended ceilings from PVC panels: photo designs and technology

The moisture-resistant properties of PVC panels are also useful for arranging suspended ceilings.

This material is used for arranging the ceiling in various rooms:

  • kitchen;
  • toilet;
  • shower, sauna or bath;


  • hallway;
  • balcony or loggia.

In most cases, in the photo of PVC panel ceilings in the kitchen, you can see a material that imitates a lining 10 cm wide. Such a finish allows you to easily install spot-type lamps in a false ceiling structure.

Other design options for lamellas can also be used for decoration:

  • imitating wood or natural marble stone;
  • matte or glossy;
  • plain or covered with ornaments;
  • decorated with printing or thermal film.

Before you make suspended ceilings from PVC panels, it is necessary to calculate the materials. The calculation scheme in this case is very simple, since there are no window and door openings on the ceilings. Stock of material - 15% of the required quantity.


Creating a ceiling from PVC panels with your own hands: videos and recommendations

Creation suspended ceilings carried out in stages. First you need to calculate the parameters of the crate, take into account the features of the lighting system, since recessed spotlights need accurate calculations and have a special installation system.

Note! For work, you will definitely need the help of another person.

Construction of the crate structure:

  1. Using the building level, mark along the perimeter of the room the points along which the profile elements of the frame base will be mounted. Fixing profiles must be carried out strictly horizontally. It is necessary to achieve the most dense placement to the wall.
  2. Using self-tapping screws, you need to fix the profile elements with transverse placement. They will hold the entire structure.
  3. A profile forming the letter L should be located along the perimeter. Further, all work is carried out to install and mask the lighting system.


Use a video review for mounting PVC panels with your own hands, reflecting all the features of the technology for creating suspended ceiling structures.

It should be remembered that do-it-yourself installation video of PVC panels in combination with the system lighting fixtures does not always reflect all the nuances of this technology. It is recommended to familiarize yourself with additional materials on this topic, since working with electricity requires serious knowledge and can be unsafe. If you do not have the proper amount of knowledge and experience, entrust the installation to professionals to avoid accidents, miscalculations and unnecessary costs.