Design

Facing panels for the facade of the house with natural stone. Facing the facade of the house with plastic panels under the stone: photos, types

Once faced with the need to finish the facade of my own house, and having an extremely limited budget, I decided to consult with friends who had already gone through this. Imagine my surprise when three out of five respondents suggested one well-known resource.

From the very beginning, I considered it as a finishing material, only facade siding, he looks, of course, trite, but he did not count on more with his finances.

I went to him, and to be honest, I was amazed, but first things first.

Types of facade panels

It turns out that siding is not only straight stripes on the walls of the house, but also a whole catalog of various imitations.

Wood.
Wild stone.
Brick.
Granite.
Marble.

Particularly liked the plastic panels under the stone. I, as a non-specialist, did not even immediately determine that this was an imitation.

Facing a house with natural stone has always been a pipe dream, but its price sometimes exceeded the cost of the house itself. After walking around the expanses of sites, I found for myself a few very important points, after which there was no doubt in the choice.

Appearance. It is possible to distinguish facade panels from natural stone only upon closer examination.
Acceptable price. Compared to other types of finishes, stone-effect facade panels turned out to be several times cheaper.
Easy installation. After looking at the installation instructions on the site, I realized that I could do it myself.
Durability. The production of facade panels from hard vinyl implies their service life of at least 30 years. When used in the most severe climatic conditions.

I found a calculator from dom sidinga, made some simple calculations, and it turned out that the final cost is even lower than what I originally planned. And the point is not only the cheapness of the material, the price was significantly affected by the fact that I will do the installation with my own hands, and what turns out, you can not put insulation under the facade panels !!!

There are two types of facade panels:

Single layer.
Multilayer.

The first option, of course, is cheaper, but it requires the installation of insulation, and the production of multilayer facade panels implies the presence of a layer of polyurethane, which plays the role of heat and sound insulation.

Correlating all the pros and cons, he highlighted the beneficial advantages of multilayer panels:

When finishing with your own hands, they do not require laying additional layers of thermal, hydro and sound insulation;
Installation is possible at any time of the year and at any temperature;
Completely insensitive to moisture;
The higher density of facade panels almost completely eliminates temperature deformation;
The polyurethane layer withstands a large number of freeze and thaw cycles.

In a word, there is no doubt. He refused the services of builders, because he nevertheless decided to do everything with his own hands, so he simply ordered the delivery of everything necessary on the Internet, and the next day he started work.

Features of facade panels and installation

I was pleasantly surprised by the fact that for the installation of plastic facade panels with your own hands, you do not need any special tool, almost everyone has everything they need at home:

Roulette
Hacksaw, preferably with a fine tooth for cutting siding
Drill with impact mechanism. And if the house is wooden, then without it
Screwdriver. (you can also use a drill)
Building level

First of all, it is necessary to treat the walls with soil, which will protect them from the fungus. Next, we make the crate on which the siding will be held. At first, in order to save money, I wanted to put on a crate wooden beam, but the specialists from the site explained that there is practically no difference in price between a bar and a metal profile, since the tree requires additional impregnation treatment.

First, using a drill, we attach holders to the wall that will fix the profile, it is important that they are located strictly along the entire height in a vertical line.

Tip: at the production stage of the crate, you need to check the level as often as possible, since crookedly installed guides will create a lot of problems when finishing.

The distance between the guide profiles should be 30-50 cm, and the step between the holders should be up to 1 m.

Guides can be mounted at the very minimum distance from the wall, since multi-layer facade panels do not need insulation, the distance is only necessary for free air flow.

The next stage of production is the installation of facade panels itself. Even before deciding to do the facade decoration with my own hands, I was convinced that the panels were first attached, and then decorative plastic corners and everything else were already on them. But after reading the instructions on dom siding, I learned that it is necessary to start from the corners and joints of the panels.

Fastened with self-tapping screws corner panels, we measure the distance between them, if it is more than 3.4 m, then at this distance you need to put an H profile that connects two panels in length.

Sometimes, for more aesthetics appearance, H profile is placed exactly in the middle of the house. In this case, you will have to cut each panel to length, and the consumption will increase slightly, but the vertical line will run in the center and fit well into the overall view.

If everything is ready, we mount the launch panel, it is located at the very bottom and the rest of the decoration will go from it. In cases where the foundation does not protrude beyond the walls, the finish is carried out from the ground itself. It is not recommended to do this, there is a special siding for the basement, which has more resistant characteristics.

Important: the starting panel must be clearly level, since a misalignment of only a few millimeters will greatly affect the finishing stage.

After the starting facade panel is installed, the easiest step remains - a set of siding. To do this, we take the panel and bring its edges into a corner and H profile, we hook the lock with the starting bar, then we fasten the panel with a self-tapping screw into a special oval hole so that the hat is in the middle of the oval.

Important: when tightening the screw, you need to make sure that it does not press the panel. The siding should hang like a self-tapping screw.

In this way, all segments of the siding are recruited and fixed under the roof with a finishing panel.

Finishing the house with facade panels is completed, now the room will become much warmer, and the house will take on a new face.

Conclusion

Facade panels for a private house under the stone

By the way, it took me two days to finish the whole house with my own hands, and this is taking into account the fact that before that I had never dealt with facade panels. Of course, many will say that natural stone cannot be compared with anything, and I probably agree with this. But often, the issue of the price of finishing materials plays a key role in their choice.

Moreover, far from everyone can do the finishing with natural stone with their own hands, it requires a special skill and a set of tools. There are no such problems with siding, and this puts it a notch above the competition.

If you want your house to look beautiful, solid and elegant and at the same time do not require repairs for a long time, then it is important to take care of a good building cladding. At the same time, not always high-quality, durable and unusual finishes require a lot of labor and impressive cash injections. In particular, the modern market offers such an innovative product as facade panels imitating stone, brick or wood, which imitate these materials so reliably that it is possible to distinguish them from natural ones only upon closer examination.

Also important is the fact that the panels can be installed do it yourself. Next, we will talk in detail about the varieties and features. basement siding, focusing on the "stone" options.

Consider the most popular options that help create an interesting visualization of masonry, incl. textures such as wild stone, rock, slate.

pvc or vinyl

They are based on various polymers, to which coloring, modifying and stabilizing substances are added, as a result, options for a wide variety of colors and textures are obtained.

Advantages plastic panels:

fireproof;
water resistant;
resistant to fading;
have a small weight;
easy to install and maintain;
inexpensive.

Weaknesses of the material:

emit toxic gases in case of fire;
become brittle in the cold.

vinyl siding prices

Vinyl siding

Fiber cement panels

They are made from sand and cement with the addition of cellulose and mineral fiber as follows: cement mortar poured onto a reinforcing frame made of cellulose, synthetics or fiberglass, the outside of the plate is covered with acrylic. Due to the high content of cement, the panel is quite solid. Some manufacturers add mica and quartz sand, which increases the strength and durability of products. And in order for them to have resistance to ultraviolet radiation and precipitation, they are varnished. Also, the use of high-quality dyes and varnishes creates unique textures and colors of surfaces.

Video - Japanese fiber cement panels

Table 1. The main manufacturers of fiber cement panels.

The name of the company	Peculiarities	Panel price / rub.
kmew	A Japanese brand whose plates are characterized by increased frost resistance due to the presence of special microgranules in the composition.	from 1500
Zierer	The German company has been producing safe, durable panels for over 30 years, which long years retain their original appearance.	from 1000
Casa Verde	The Russian company has been producing panels and thermal panels since 2012, the warranty period is 30 years, and the estimated one is 100 years.	from 1000
TechnoNIKOL Hauberk	For more than two decades, the Russian manufacturer has been manufacturing panels with an outer layer of natural basalt, which ensures a long service life.	from 500

Reference! Fiber cement panel is obtained by pressing, which takes place under pressure 600-650H/cm 2 , and autoclaving at a temperature 175 degrees. After manufacturing, each copy is tested for compliance with the declared characteristics.

Appearance of fiber cement panels

Advantages:

strength is the main advantage, which corresponds to the quality of porcelain stoneware facade tiles;
fire resistance;
resistance to low temperatures and extremes allows you to operate it even in harsh climate conditions;
equipped with ventilation slots, thereby allowing air to circulate freely between the panel and the heat-insulating layer;
has a heat-insulating and sound-absorbing function;
can be used both outside and inside the building;
no preparation is required before finishing.

Disadvantages:

not too presentable appearance, as a result of which, after installation, painting of the panels is required;
high price.

Insulated panels

They are based on insulation, and the front side is a designer layer of polymer coating, consisting of polyvinyl chloride, resin, foam and stone dust, which allows you to clearly highlight the stone texture, emphasize shale rock, rubble and wild stone.

Schematic composition of the insulated panel

Advantages:

do not exert strong pressure on the foundation;
the finishing process can be carried out in any climatic conditions;
quick payback, due to the fact that a house sheathed with panels can be heated half as much;
fireproof;
do not allow mold and fungi to multiply;
very durable.

Disadvantages:

thorough surface preparation is required;
high price.

Prices for thermal panels

Thermal panels

Stone or brick effect tiles, ceramic and clinker

This type includes thermal panels, they are clinker facing material with polyurethane foam. The tile is made from clay with a mineral composition. Chamotte is added to the clay for heat resistance.

Advantages:

safe for the environment;
moisture resistant;
easily tolerates temperature changes;
the service life is several decades;
great thermal insulation;
not whimsical in care;
easy to repair;
due to its low weight, it does not exert a load on the foundation;
not afraid of exposure to ultraviolet rays.

Weak sides:

high price;
the fragility of the decorative layer, and in some cases, the insulation.

Mounting

Step-by-step instructions for finishing a house with fiber cement panels

We will need tools such as:

Bulgarian;
screwdriver;
self-tapping screws;
level.

Prices for angle grinders (grinders)

Angle grinders (grinders)

Panels come with evenly cut edges, and there are panels with tongue-and-groove locks. Facade kits are completed with the same elements as siding: corners, extensions, platbands, start and finish strips.

Important point! Some brands for fastening panels already have special kleimers, while others will have to drill holes for roofing screws during installation.

Finishing frame house with vertical posts

We lay the insulation between the racks.
We fix the basement ebb element to protect our basement. Almost every manufacturer offers this element complete with fiber cement panels.
Then we install the hydro-wind protective membrane, we make overlaps at the corners from 100 to 150 mm, we fasten them with a special stapler.
We install clamps on the corner, on the tongues of which we fasten the corner element. As for the inner corner, a special inner seal is provided, which is placed directly into the corner, sealing occurs on both sides.
Then we put the first panel and attach it with the help of clamps to the racks. Between the corner element and the panel, if there is no groove-comb system, a seam seal is placed. There is an insulator on the panels. When there is an adjunction between them - panel to panel, then through this insulator the panels will be waterproofed.
Then we strengthen the second panel. Again, if there is no tongue and groove system, the beginning of the panel is reinforced with clamps, which are attached at the beginning and end of each panel, as well as to the vertical posts of the batten. A special seam sealant is placed between each panel. If there is a groove-comb system, then a clamper is installed in the center of the joint from above, which will hold two panels at once.
As for the window opening, before installing the panel, a special bar is placed under the window, which is also necessary for air circulation. In thickness, it should be the same as the kleimers. From the sides of the windows we install a seam seal, and above the window - a seam seal and a ventilation bar, as well as under the window. A window sill seal is also attached with a tail to drain water if condensate gets in. The panel is installed.
To complete the top of the wall, a ventilation strip is installed on top. A panel holder is placed on the ventilation bar and finishing panels are installed.

Installation of panels on a wooden crate.

Important! There must be a gap between the horizontal bar under the window and the vertical bar of at least 30 mm. This is done for better air movement.

We install a basement drain.
We install the crate. At the corners and at the joints of the panels, the width of the plank should be about 90-100 mm, and the thickness is 25-40 mm. Intermediate strips: 45- 55 mm width, and the thickness is the same as the corner strips.
The window opening is also trimmed. There is a nuance here: first, the lower bar is attached flush with the window opening, and then the bars are attached to the left and right sides and the last bar covers the top.
After installing the crate, a starting plate is attached around the perimeter. The initial panel will be attached to it.
Then a corner element with a kleimer is attached, which are used here in a different shape and with two antennae.
We also fasten the corner panels from above with ordinary clamps, we mount seam seals to the rails to connect the joints between the panels.
Then the same procedure takes place, which was described above, using kleimers and seam seals. A sealant is also placed on the inner corners, one panel is installed, reinforced with a clamp, then a seam sealer is placed in another plane and a panel is installed, which is also reinforced with a clamp.
Treatment window openings practically also does not differ from the technology described above. Above the window we lay a seal with a tail to drain water if condensation accumulates. Three pieces are placed on a standard window. A ventilation bar is placed on top of the thickness of the kleimer, the rest of the steps are the same.

Advice! In order to save on these elements, you can get out of the situation as follows: take a panel of one color at the corners, and use another around the perimeter. The only thing is that you have to saw down the panels on one side at an angle 45 degrees so that the joint at the corner is tight.

Step-by-step instructions for finishing facade panels with insulation

Consider the option when the installation takes place on a bare wall without a crate and a hydro-wind protective membrane.

To work, you will need tools such as:

hammer;
rubber mallet;
grinder for sawing panels;
perforator;
dowel;
pliers.

Prices for popular models of rotary hammers

Perforators

Work order:

The installation takes place by attaching the plates to special antennae, for fixing which a hole is drilled in the wall with a perforator, and the antennae is attached to the dowel. The antennae is attached to one hole, the edge of the antennae is left unattached to connect with the next row of panels.
The rows are attached to each other with the same antennae: one antennae goes behind the insulation of the other panel and holds the edge. The edges for alignment are lined with a rubber mallet.
To avoid heat loss, a special foam is applied to the insulation, which fills all the gaps between the tiles during the expansion process.
The corner is made like this: the edge of the tile should protrude, the size of the protrusion is equal to the thickness of the tile. A heater is selected from the edge, due to which a joint with another tile occurs.
The window opening also does not cause difficulties: the tile is sawn along the window opening. If the window opening goes deep, then sawdust tiles are inserted into the recesses, which are attached to the metal strips with a self-tapping screw. Above the window, two metal strips are attached to the dowels, and a tile is attached to them, in which a hole is drilled for this, a dowel is inserted there, and everything is also attached with a self-tapping screw, which is subsequently painted over.

Advice! For beauty, you can use the following finishing process: use tiles of a different color in the corners and along the edges.

Step-by-step instructions for finishing with stone-look clinker tiles

Prices for Ceresit glue

Glue Ceresit

For work you will need:

special glue;
tile cutter;
putty knife;
a thread;
brush.

Important! You need to start work with window and door openings.

Step 1. Treat the surface with glue.

Step 2 Moisten the tile with water, apply glue, make grooves.

Step 3 After laying the first row, pull a thread along the wall, which will serve as a beacon for laying other rows.

Price for popular models of laser levels

Laser level

Step 4 When gluing tiles, you must remember to leave seams identical in size to the thickness of the tile.

Step 5 Fill all seams with mortar and wipe. Result

Houses sheathed with stone-like facade panels look not only elegant, but fully correspond to your ideas about the appearance of the building - it can be aged, conveying the style of your favorite era, or ultra-modern. At the same time, such a coating has long term service, which will provide an attractive appearance for many years. If you want to update the design of the facade, then dismantling and new montage is very easy and can be done on your own. Another important factor is the absence of the need to care for the panels - only occasionally they can be rinsed with water to remove dust.

Especially exclusive are the houses, the facade panels of which are made under wild stone. In this case, their solidity and importance border on impregnability. However, their owners all year round they live in comfortable conditions, because, like natural stone, these panels keep the interior cool in summer, and protect them from piercing winds and severe frosts in winter.

MittenThe production of panels has been carried out since 1959, the main advantage of the products is the ability to withstand a temperature range from -50 to +50 degrees ° C.from 415 KaycanA professional brand with more than 40 years of experience in producing panels with electronic equipment, which guarantees high quality and stability. geometric characteristics each instance.from 179 RoyalGives a 50-year warranty on its product, and the catalog contains the most wide choose colors.from 155

Reference. Over the past decades, Russian products have also become competitive. In particular, firms Alta siding, the panels of which withstand frosts down to -50 degrees ° C and heat - up to +60°C, price 1 pc. from 124 rub, And Nordside, which does not use harmful and toxic substances in the manufacture and guarantees 50 year service life, panel price from 105 rub.

Table 3. Leading manufacturers of stone or brick effect tiles.

brand name	Peculiarities	Panel price / rub.
Nailite	The US brand produces tiles in 10 unique series, each of which can withstand temperatures from -50 to +50 degrees C. The warranty period is 25 years.	from 890
Dock-R	The German quality of the panels ensures their long service life, confirmed by a 50-year warranty.	from 350
grand line	The Russian manufacturer produces premium-class tiles, for which it gives a lifetime warranty.	from 260

And in conclusion, I would like to wish that no matter what type, design and texture the walls of your house were, the main thing is that an atmosphere of love and understanding always reigns inside, filling the hearts and souls of the household with warmth, comfort, light.

Today, stone-like plastic panels are widely used for finishing building facades. for various purposes. The complex of positive characteristics of the material cannot be overestimated, since the main requirements for them, such as thermal insulation, moisture resistance, long service life and aesthetics, are on high level. Plus, the cost of such a finish is much lower than natural stone.

Types of panels for facade cladding

By decorative properties, all artificial imitators are divided into the following types:

Material Features

Facade panels under the stone are divided into two types:

With a single-layer structure, that is, made of PVC and its derivatives.
Combined panels.

The second type has an advantage over the first. So, outer layer made from polymers or other materials, and the inner one is made of expanded polystyrene.

This material is an excellent insulator. So, we found out that the decorative facade has an addition in the form of a heater. Sometimes polystyrene acts as polystyrene. Styrofoam is connected to a plastic coating that imitates stone without the use of glue and locks.

This material has main feature- is he perfectly tolerates temperature changes and moisture. Moreover, he is able to endure its abrupt changes within one day. This completely eliminates its deformation due to the low coefficient of linear expansion. Such panels, depending on the taste of the customer, can be presented in any color and texture.

The main advantage of this material is its low cost compared to natural finishing stone. Besides, installation work much easier and take less time, which cannot be said about laying stone. Installation of such panels can be carried out in any weather, while there is practically no dust.

Due to the fact that the corner fastening of the panel is provided, the time for drawing the corners is significantly reduced. Cladding material has a small weight, so the load on the wall and foundation is significantly reduced. The installation process is simplified so much that even an adhesive base is not required.

Decorative stone effect panels for facade cladding

Advantages of facade panels under stone

Decorative

Summing up all of the above, one thing can be said that there has not yet been such a building material that would change the appearance of the whole house in a short time. Thanks to this finish, which has excellent decorative properties, the facade can be transformed before our eyes. Moreover, the installation is carried out without the use of expensive equipment. The panels are attached to each other, which speeds up the process of cladding the house, everything happens without installing any special frames.

For country house facade decoration with decorative panels under the stone will be a great solution. Any a house in such a garment will be transformed and come to life against the backdrop of the composition of the local landscape. A wide palette of colors allows you to choose an individual shade that fits perfectly into the surrounding countryside landscape.

Insulated

When installing panels under a stone, two problems are solved at once. One of them is in external beauty, and the other is in comfort. After all, the foamed layer of material is perfectly used as a heater. Styrofoam excellent thermal insulation characteristics, which are significantly superior to polystyrene. Thanks to this, two goals are achieved, which are warming and updating.

Thus, there is no need for additional expenditure on facade insulation. This technology can significantly reduce heat loss, especially noticeable in the cold season. Plastic front sheets under a stone well protect the house from dampness and a fungus, such material completely excludes also a mold.

Manufacturers and price in Russia

The leaders in the production of facade panels under the stone are the following companies:

German leading manufacturer Döcke-R;
Canadian firm Novika;
Nailaite (USA);
Russian company Alta Profile.

Price

The cost of facade panels for facing a house depends on the quality, material, as well as imitation of the type of stone. In addition, the price of panels and services also depends on the region and can vary significantly. Cost may vary depending on policy. trading company. Medium the price of this material is in a wide price range from 300 to 1500 rubles. Therefore, you can approach the choice of material both taking into account taste, and from the side of a suitable price.

The finishing material in our country is sold at an affordable price. So, the collection "Rocky Stone" will cost about 430 rubles. There are more expensive models, for example, “Natural Stone” will cost 580 rubles already.

You need to know that the price is indicated for one package, which contains 10 pieces. They are enough for 5.32 m2. To clad the facade of a house with an area of up to 100 m2 with stone-like panels, you will need an average of 20 packs with a margin for cuts. As a result, the price decorative finishes panels under the stone will be about 12 thousand rubles. It is worth counting additional accessories. It should be remembered that the finished facade will be used for 50 years, then this amount will not be so large.

Thus, facade panels imitating stone will become not only excellent design solution when designing the appearance of the house, but also will result in significant financial savings when compared with the cost of natural stone. This cladding will create a sense of the integrity of the structure of the building and give it some majesty, as, indeed, the stone itself.

Facade panels for exterior finish- This is a popular option for wall cladding and giving the building a finished look. Our catalog contains a variety of panels for facade decoration, imitating stone and brickwork domestic and foreign manufacturers.

Facade panels under stone and brick

Facade panels in stone and brick look show a wide variety of colors, textures and models. Thanks to this feature, you can give any building a unique look. However, apart from the beautiful decorative properties This finishing material has important practical qualities:
Provides protection of facades from precipitation and other negative natural phenomena, so you can definitely forget about the periodic renovation of the facade (depending on the manufacturer, this period can be 20-50 years);
Increases thermal insulation performance: drafts practically disappear and thus heat loss is practically reduced to nothing. In addition, sound insulation improves, so extraneous noise from the outside will hardly disturb you;
The use of finishing panels can hide flaws, geometric deviations and uneven facades.

Facade panels: materials

Panels for the facade are based on various materials: aluminum, zinc, steel, coated on top with a polymer layer. It is thanks to the top coat that this type of finish exhibits a wide variety of colors, patterns and textures. The metal sheet located at the base of the panels provides them with strength and durability.

Buy facade panels in Moscow and the Moscow region

Buy facade panels with delivery in Moscow and the Moscow region at the most affordable prices You can in the store building materials Krovla.msk.ru. We are pleased to offer you a wide selection facing panels various textures, colors and models, so that you can surely choose the most suitable option. You can also purchase everything you need to organize a roof from us.

There is a wide variety of materials for cladding and decorating the facades of houses. The naturalness of natural stone is popular. Facing the facade of the house with plastic panels under the stone looks expensive and beautiful. Such a design, as shown in the photo below, will fit into any natural and urban environment.

Types of materials

Stone decoration will be appropriate only for new houses, since the stone is very heavy and the structures of old houses may not withstand such installation.

Stone structures are made from various materials. It can be wood, plastic, cement structures, as well as products from combined structures.
At the moment, plastic panels are very popular, as they have good performance properties and an affordable price category.

The structures serve not only to decorate the facade, but also protect it from negative natural influences. They also significantly extend the service life of the building and protect the supporting structures from moisture and cold. The panels do not allow the penetration of noise from the external environment.

For facing the facade of the house, panels are used that are twice as thick as Wall panels. This thickness helps to resist natural influences. Also, the facade panels have a pattern of large, natural, natural stone, which has a rich color.

Cladding materials are of the following types:

Siding.
Metal constructions.

The properties of houses, operating parameters, as well as its durability and practicality depend on the type of finish.

Two types of stone imitation products for house cladding:

Made from PVC single layer panels.
Combined, functional, two-layer panels.

The second type of panel is very practical and performs two functions:

facade protection;
wall insulation.

It is wiser to install the second type of panels, as this significantly saves the time required for separate insulation and, of course, saves money.

For materials, the following types of imitations are used:

under rubble stone;
imitating textiles;
under a hewn stone;
mosaic;
under natural stone;
under concrete.

Features of plastic panels

Installation of structures has a number of significant advantages:

Lightness - do not create a load on the facade.
Racks under mechanical influences.
After the cladding, the building takes on an improved appearance.
A wide selection of panels of different design ideas.
Buildings do not require additional maintenance.
Panels can be installed independently, subject to the required technology.
Installation does not require specialized equipment, as the panels are lightweight.
Value for money.
The facade, lined with panels, will serve for a long time.
In case of damage, it is very easy to repair.
Availability - in all stores you can find similar products.

In addition to the advantages, there are also negative countries:

it may be difficult to choose a color, since there is a huge amount of tint range;
panels in the presence of fire begin to melt;
sunburn is also a negative factor.

How to make facing

When implementing self-assembly panels, you must have the appropriate devices: tape measure, level, drill, hammer and others.
Before installation, surface preparation is carried out. It should not be dusty and smooth. In cases where the base is wooden, it must be treated with specialized insect repellents.

Installation is carried out in three steps:

Preparatory stage.
Frame fastening.
Basic installation.

Products are fixed on the starting and finishing profiles. Consider the installation process common to all types:

At the first stage, the first structure is fixed to the starting base in the lower corner.
Each subsequent product is attached from left to right, we form a row from bottom to top.
The first base is fixed with a screw, the rest are snapped into place with a vertical lock.
Fasten with screws.
The materials have the same pattern. To give a natural look, you need to move them.
You can make repairs at any temperature, but it is not recommended to do this below -5 degrees.
It is recommended to purchase designs of the same brand, since each company uses different sheet sizes.

The design of the building with natural stone goes well with metal products, trees.

The price of the panels depends on the type and functional features of the material. The cladding of the facade of the house with plastic stone-like panels shown in the photo goes well with landscape design site.

The stone-panelled private homes are sure to grab attention on the streets. When using several colors, the individuality of the building is emphasized. So finishing in gray-green tones will create Scandinavian style. Pastel colors are traditional. Cottages with dark cladding will fit perfectly into the woody landscape.

Stone effect panels will be an excellent addition to the overall design of the house area, and are also one of the economical options when decorating a house. Panels give the house naturalness and naturalness.