Pipes

How to finish a painted interior door. How to update an old interior door to a bathroom or toilet inexpensively? What paint do we paint

Over time, even the highest quality doors become unusable. The material shrinks or deforms, the coatings wear off and fade. In this case, it is necessary, or to give the old doors the new kind, restore them. And what happens even more often is that the type of doors can simply get bored or not meet your taste. In such a situation, replacing with new ones is not at all advisable. It is better to update the doors with your own hands, think about creating a new design for her.

Stage 1: removal of the old coating and processing of the door

If there are deep scratches or crevices on the surface of the door, or the door is slightly lopsided, it is best to remove it and put it in full order. And before any subsequent finishing, it is worth getting rid of the old coating. For such work, it is desirable to have at least basic knowledge of working with wood and a set of tools.

To upgrade a wooden door, remove it from its hinges. Dismantle all fittings (handles, locks, latches, etc.), if they are no longer suitable, it is better to replace them. At the same time, it is desirable to change all the handles and trim on the doors within the room so that they are all in the same style.
If there is glass in the door, then carefully remove the glazing beads and expose it. After that, you can already begin to remove the old coating. Use a blow dryer to heat up a layer of old paint, and when it begins to soften and bubble, remove it with a spatula.
When the last paint is removed, proceed to seal the cracks and smooth out the scratches on the surface of the wood. This can be done using special putties for wood and putty. After the materials have dried, sand the surface and sand well.
Cover the surface of the door with stain or drying oil. This will give the surface the desired shade or simply protect it from moisture.
If there were glasses, then insert them back. It is best to use new glazing beads, they cost a penny, and it is better than cleaning the old ones.

In this form, the door is ready for further decoration and decoration.

Stage 2: choosing and decorating

But how can you update old doors? To do this, choose one of the listed design options. Before any work, it is worth bringing the door to normal condition. This is either the restoration described above with the removal of old coatings, or simply a thorough cleaning and drying so that the new decor elements are normally fixed on the surface of the door.

Painting

The easiest and most reliable way will be painting. If your door is made of solid wood or has a wood veneer paneling, then you can open it with varnish or your favorite paint color. In any case, it is best to paint the door with a brush or spray. With a brush, spend all the time along the fibers, then the paint or varnish will normally fall into all the recesses and irregularities.

Pattern decoration. moldings

In addition to painting in a solid color, paints of other shades or colors can be used to create some kind of image on the door or simple drawing. Alternatively, you can paint the door in one color, and the protruding parts (moldings) in another, contrasting with the base. If the door is flat without relief and moldings, then you can either depict their emulation with a pattern, or use polyurethane or wooden carved slats. The latter are pre-painted in the desired color and glued to the surface of the door.

You can try to depict a drawing or painting on the door. About this on the example of decorating walls.

Pasting with wallpaper, paper materials or fabric

You can decorate interior doors with your own hands in more interesting ways. Now it will not be a problem to find in stores or order on the Internet murals specifically for doors. They are already preparing standard sizes door leaf.

In addition to photo wallpapers, which, by the way, are not cheap, you can use other materials for decorating doors. If the room is decorated in a certain style, then the door can be decorated to match it. For example, if this is a children's room, then you can use the pages of various educational children's publications or a variety of coloring pages. For the kitchen or dining room, you can pick up pages with images of delicious and favorite dishes and stick them on the door.

If paper material is selected, then first hold it in cold water, and then carefully apply PVA glue to the entire surface of each sheet and attach to the door. Carefully smooth the entire surface of the sheets so that no air bubbles remain under it. In the future, it will be almost impossible to get rid of them. Once the glue and material is dry, paint over the entire surface with clear varnish to protect your art from fading and moisture.

In a similar way, you can use various fabrics as a material for decoration. The abundance and variety of fabric design will allow you to realize a variety of design ideas.

This is interesting: doors decorated with paper for the New Year

Stained glass and sandblasting

If your door has glass inserts or the entire door is glass, then stained glass design would be an excellent option. Buy stained glass paints water based not a problem now. Draw a thumbnail of the image you would like to display on the glass and divide it into parts for each individual glass or to make it easier to transfer to a large glass. Outline the entire image with dark or even black paint with a thin line. After the contours have dried, start filling in the necessary spaces with paints of other colors.

Alternatively, you can apply the image to the glass using sandblasting technology. To do this, it is better to contact a special workshop where they will perform such work.

Use of vinyl stickers

A huge variety of vinyl stickers will allow you to modify the doors in the easiest way. To do this, it is not even necessary to get rid of the old coating or bother with disassembling and removing the door. With the help of vinyl stickers, small scratches and scuffs on the door leaf can be hidden from sight. Again, they can be subsequently painted in different colors.

To apply vinyl stickers, carefully separate the backing from it and apply it to the previously cleaned surface on the door. After you press evenly over the entire area of the sticker and check that everything is firmly fixed, you can remove the film that protects outer part stickers. If the film does not separate well in some places, then heat it up with a regular hair dryer turned on to heat the air.

Original design methods

Quite an exclusive option on how to update the old interior door, this is the use of various bulk materials for pasting the entire surface. Oddly enough, buckwheat or rice is perfect for this. In the case of buckwheat, the result will be a very peculiar and beautiful result. To stick the cereal, you can use PVA glue or ordinary wallpaper paste. After complete drying of the surface, it is better to open it several times with varnish to protect it from moisture. And do not worry about the integrity and durability of such a coating. Dry cereals are not subject to rotting or deterioration, and the varnish coating will protect it from moisture and prevent it from swelling.

With a little effort and imagination, you can turn an old interior door into something stunning and more attractive, or at least change its boring look.

(No ratings yet)

Discussion:

Can't decide to update. kitchen set. it is long, in glass cabinets, which are framed by golden stripes with curves at the corners. Everything is already tired, especially since the veneer began to move away. I want to tint the glass from the inside with a transparent film with patterns. I looked at some of your options, there is an impetus for the idea. Thanks to!!!

Refurbished bathroom door last year. I suffered with a building hair dryer, especially since I did not remove the door. And now it turns out there are all kinds of gels to remove the old coating. How much easier would that make the job. And now I’m on fire with photo wallpapers, as you look at what choice there is, my eyes run wide. I will definitely do my next feat with doors with photo wallpapers.

Paint for sale, with which the effect is created - craquelure. You need two bottles to work. The first balloon creates the base, mostly white.
The second balloon after application creates the illusion of a cracked surface. Gold or silver colors. Great choice for doors.

I made a vintage-style door for myself in the bathroom. For this, I bought specially plastic pebbles for the aquarium, shells and plants. I glued it all with a glue gun. Since I glued everything randomly, there was a lot of free space. And something was missing. Plus to everything , ordinary glasses somehow looked dull on such a door. Then I cut the tile that remained from the laying and also put it into motion. I also added old crumbling beads. Everything that was at home in a marine theme went into business. regular paint on the glass in blue tones.

In the bedroom, I pasted my door with wallpaper on both sides, it turned out very cool. But now I read the article and realized that there were so many other good options. googled looked at pictures with vinyl, already fell in love, we must definitely try something new to update.

For the patina effect, I used Aqua-color water-based acrylic pastes to imitate a metal surface. True, I did not use them to decorate the door, but covered the cabinet handles. It's just that there are small jars in the kit, it may not be enough for the door. But for sure there are other patinating compositions in the public domain ... Ask around, look)

Of the methods described above, I used painting moldings and panels in contrasting shades, pasting wallpaper. it turned out very well, because Each door matches the style of its room. I don’t think that someone will dare to decorate the doors in the room with buckwheat. But this is a personal matter for everyone. But one of my doors has not been restored yet - I really want to make it “antique” with patina. I can't find detailed technology anywhere. can someone share a secret?

By clicking the "Add comment" button, I agree to the site.

The nuances of the restoration of the old door with your own hands. Ideas and methods, photos.

A person associates his home with a place of rest. Therefore, he tries to create coziness, choose an interior and a pleasant color scheme in order to fully realize this.

On the other hand, everything in our world tends to become obsolete and collapse. Our homes and their interiors are no exception.

Updating something around us, we awaken creative energies in ourselves, we feel creators.

Although most types of interior work require special in-depth knowledge and skills to perform them, we are quite capable of updating interior doors on our own.

Let's talk about the features and methods of reconstructing old doors in more detail.

How to make a new one from an old door with your own hands: options, photos, tips

photo of an old door before and after restoration using decoupage technique

It is important to prepare it before updating the old door:

remove the doors from the hinges and lay on a flat horizontal surface
fold all accessories separately or prepare for disposal if it has become unusable
if there are glass elements, carefully remove the glazing beads and then remove the breakable parts
if the door has been treated with paint, turn on the building hair dryer and gradually warm up its surface
arm yourself with a piece of coarse sandpaper and remove bubbles of old paint
replace the paper with another one with a finer abrasive and again go over the entire surface of the door
carry out the final grinding with sandpaper with minimal abrasiveness
treat the surface of the door with a special putty for wood products
after complete drying, clean the doors in 3 steps with sandpaper of different abrasiveness
fix the result with drying oil or stain
then carry out those types of work that are necessary to update the appearance of the door
if there were glass elements in it, put them first and then new glazing beads for a fresh color / design

As examples, look at the options for updated doors in the photo.

embodied ideas for decorating and restoring an old interior door, example 1

embodied ideas for decorating and restoring an old interior door, example 2

embodied ideas for decorating and restoring an old interior door, example 3

embodied ideas for decorating and restoring an old interior door, example 4

embodied ideas for decorating and restoring an old interior door, example 5

embodied ideas for decorating and restoring an old interior door, example 6

embodied ideas for decorating and restoring an old interior door, example 7

embodied ideas for decorating and restoring an old interior door, example 8

embodied ideas for decorating and restoring an old interior door, example 9

embodied ideas for decorating and restoring an old interior door, example 10

embodied ideas for decorating and restoring an old interior door, example 11

embodied ideas for decorating and restoring an old interior door, example 12

embodied ideas for decorating and restoring an old interior door, example 13

embodied ideas for decorating and restoring an old interior door, example 14

embodied ideas for decorating and restoring an old interior door, example 15

embodied ideas for decorating and restoring an old interior door, example 16

embodied ideas for decorating and restoring an old interior door, example 17

embodied ideas for decorating and restoring an old interior door, example 18

embodied ideas for decorating and restoring an old interior door, example 19

embodied ideas for decorating and restoring an old interior door, example 20

embodied ideas for decorating and restoring an old interior door, example 21

embodied ideas for decorating and restoring an old interior door, example 22

embodied ideas for decorating and restoring an old interior door, example 23

embodied ideas for decorating and restoring an old interior door, example 24

embodied ideas for decorating and restoring an old interior door, example 25

embodied ideas for decorating and restoring an old interior door, example 26

How and with what you can update the color of old wooden doors: ideas

girl paints an old wooden interior door with white paint

After you have completed the restoration work on the surface of the old interior door, choose a new color for it.

Among the ways that can help you in this moment, we note:

Painting with stain, paint or opening the wooden surface of the door with varnish.
Remember for best result brush along the fibers, then all the cracks will be filled with a dye.
Accents on moldings, or painting the protruding parts of the door with contrasting or similar colors. In the absence of such elements, glue them from wooden or polyurethane slats and paint.
Artistic painting, coloring through stencils.
The method is suitable for creative owners who want to bring originality to their interior.
Pasting wallpaper, large drawings on paper, pieces of fabric. Decoupage.
In this case, follow all the requirements for fixing the material on the surface of the door - soak it with water, glue, and process it from above with a jet of hot air.
Stained glass painting on glass.
If you are good at drawing or stock up on interesting stencils, buy special stained glass paints and decorate the glass elements of your old door.
Sticking vinyl stickers.
Note that this method saves you time preparing the old door. In other words, you can not even remove it from the hinges, but immediately glue the vinyl elements.

How and with what can varnished doors be updated?

a man removes the old lacquer coating from the doors for their restoration according to a new design

To carry out restoration work, remove the old varnish from the door in one or more of the following ways:

sandpaper
grinder
chemical solvent

The first method was discussed in the previous section. The second method will significantly speed up the process of removing the old varnish coating. And the third one has one caveat - the varnish can remain selectively on the door leaf. Therefore, be sure to polish the latter.

After removing the old layer of varnish, sanding and drying the doors, decide on their new design, for example:

apply new varnish or laminate,
paint the desired color
paste wallpaper / photo wallpaper or other self-adhesive tape with imitation, for example, under natural wood,
apply freehand painting, copying a specific drawing, or under a stencil,
decorate the door by gluing loose cereals - rice, buckwheat. Be sure to apply a layer of varnish on top to better fix the material.

How and with what can veneer doors be updated?

photo of renovated old veneer doors

One of the most common problems at veneer doors - this is a swelling of the canvas in some areas. Therefore, first prepare it, carry out restoration activities before updating.

To eliminate the problem of swelling of the canvas will help:

Iron.
Heat it on medium and iron the swollen surface of the door, folded on a horizontal stand.
Wet rag.
Moisten a cloth flap with water and spread it on the problematic surface of the door. After a quarter of an hour, remove and wait for drying.
PVA glue.
Draw it into a syringe and gently insert it under the swollen surface of the door. Smooth the area with a dry cloth.

To eliminate cracks and chips on the old door of the material in question, stock up on strips of veneer of a similar color.

Cut out the strips corresponding to the parameters of the repaired surface.
Cut off the excess with a scalpel after applying to the place of the chip / crack. At the same time, keep in mind that the fibers of the patch should be perpendicular to the restored door.
Process door leaf special putty and wait for it to dry completely.
Use double-sided adhesive tape to secure the veneer pieces.
Sand the joints.

When your old door has only minor scratches and chips, wax them:

liquid
pencil

In the first case, put a couple of drops into the rift and immediately walk with a dry rag to remove excess. Before doing this, be sure to clean the door of dust and dirt, and also grind the surface.

In the second, tear off a piece from the wax pencil, knead it in your palms and stick it on the problem area. Wipe off the mark with a rag. Do this only on a previously cleaned and prepared door.

Update prepared old door veneer will help you:

If you masked chips and scratches on the door with wax, then remember that varnish and paint will not cover them. Or linger on it for a short time, and then crumble.

How and with what can panel doors be updated?

old panel doors after paint renovation, decor options

Paneled doors in the interior look interesting. However, it is not always convenient to process their frayed surface. We will not go into details. Let's take a look at restoration options.

Successful solutions:

painting in several colors with highlighting protruding places
wallpapering in segments, adhesive tapes along the contour, on panels
decoupage of individual segments
varnishing

The cardinal method is the analysis of door panels and their replacement with laminated hardboard. To do this, you sheathe the door frame with it and carefully select the color when gluing its ends.

If there is glass in the door, decorate it with special paints or imitate a stained glass window. Stencils for decoration are also suitable.

How and with what it is possible to update the doors covered with paint?

man painting old previously painted interior doors

Your first task is to remove the old paint from the doors and prepare them for restoration work. Their sequence:

decide on the location of the door in space - either lay it on horizontal supports, or remove it from the hinges and leave it vertically,
go over the entire surface with a spatula and remove a layer of old paint,
sand with sanding paper
treat with a special primer for wooden surfaces,
let dry and sand again

Seal the areas of the door that you do not plan to paint or varnish.

How and with what can paper doors be updated?

updated paper doors in the interior

Renew paper doors with lightweight materials that will not weigh them down and provoke leaf breaks. For example:

self-adhesive film
decoupage
gluing of individual elements, for example, paintings, three-dimensional drawings
painting with paints
stencils

How and with what you can update an old door frame: ideas, photos

a man measures the level of the door frame in the process of its restoration

The restoration of the door frame should be remembered when you are updating the old door leaf. Of course, fiddling with the first one is less convenient, since it will not work to remove it.

The door frame processing technology is similar to those discussed above for doors. Choose carefully the shades of paint and stain, as well as the color of the self-adhesive tape, wallpaper, so that this area on the wall is in harmony with the updated door leaf.

Below are a number of interesting door frames after restoration with their own hands.

updated door frames to match the interior and doors, example 1

self-adhesive door frame decor elements, example 2

self-adhesive door frame decor elements, example 3

How and how to glue the door beautifully?

beautifully glued interior door after renovation

Among the common ways to decorate an old door is to glue a new coating in whole or in fragments.

For this you will need:

the cloth
leather and its substitutes
photo wallpaper
metal rivets, beads
patchwork
cut fragments of a picture, for example, maps of the world

To stick this or that material, select an effective adhesive, for example, PVA glue, special for wallpaper, adhesive tape, double-sided self-adhesive tape.

How beautiful to wallpaper the door?

the old door after the renovation is pasted over with wallpaper

The main thing is to follow the technology of wallpapering.

First, prepare the door leaf for the update. The technique was presented in the first section of the article.
Decide on the color and texture of the wallpaper.
Apply special wallpaper glue to the surface of the door and attach the paper decor element.
Smooth the result with a dry rag.
Trim the protruding edges with a utility knife.
Wait until the wallpaper on the door is completely dry.

Decorate as you wish:

molding
designer chips, for example, small shells and a cut net, glued on top and covered with paint

In addition to the usual wallpaper, popular:

photo wallpapers with the image of three-dimensional objects / paintings
decoupage
self-adhesive tapes

How to update an outdated metal front door?

old metal Entrance door after update

Metal doors also tend to become morally and physically obsolete. Having set out to update them, keep in mind that the approach and methods will be different for the external and internal parts of the front door.

So, the following solutions will update the interior:

drawing with a stencil
art painting
full door mirror
leatherette upholstery
self-adhesive film
laminate

And for outside doors fit:

MDF panels
laminate

To fix any material on the surface metal door you will need an adhesive liquid, such as liquid nails when working with wood flooring.

How to beautifully decorate an old door for a nursery: ideas, photos

do-it-yourself door in the children's room

Children's room is an area of creativity, leisure and intellectual work of the child. Consult with him before you begin to update the door to the nursery.

Better yet, involve the child in the process.

For inspiration, let's add a row ready-made solutions decorating the door to the children's room.

options for decorating doors to a nursery after updating them, example 1

options for decorating doors to the nursery after updating them, example 2

options for decorating doors to the nursery after updating them, example 3

options for decorating doors to the nursery after updating them, example 4

options for decorating doors to a nursery after updating them, example 5

options for decorating doors to the nursery after updating them, example 6

options for decorating doors to the nursery after updating them, example 7

options for decorating doors to the nursery after updating them, example 8

options for decorating doors to the nursery after updating them, example 9

options for decorating doors to the nursery after updating them, example 10

options for decorating doors to the nursery after updating them, example 11

options for decorating doors to the nursery after updating them, example 12

options for decorating doors to the nursery after updating them, example 13

How to beautifully decorate an old kitchen door yourself: ideas, photos

renovation of an old kitchen door with mosaics

In order for the door to the kitchen to change after restoration, choose the concept of its decor. It can be:

painting
varnishing
decoupage
gluing wallpaper and any adhesive surfaces
art painting and stencils
stained glass elements
mosaic and gluing loose, small elements

Implemented ideas with updated doors to the kitchen, see below.

embodied ideas for the restoration of an old kitchen door in the interior, option 1

embodied ideas for the restoration of an old kitchen door in the interior, option 2

embodied ideas for the restoration of an old kitchen door in the interior, option 3

embodied ideas for the restoration of an old kitchen door in the interior, option 4

embodied ideas for the restoration of an old kitchen door in the interior, option 5

embodied ideas for the restoration of an old kitchen door in the interior, option 6

embodied ideas for the restoration of an old kitchen door in the interior, option 7

How to beautifully decorate an old bathroom door: ideas, photos

options for updated doors to the bathroom in the interior

The bathroom is a special place in any home. Here we restore beauty and relax after working days. I want the door to it to have its own style.

If you are currently updating it, consider these ideas:

drawing through a stencil
self-adhesive film
imitation of stained glass and paneled elements
combination of colors when staining fragments
mirror interior
photo wallpaper

For more details, see the implemented ideas for decorating the bathroom door in the pictures below.

bathroom door design options after do-it-yourself renovation, example 1

bathroom door design options after do-it-yourself renovation, example 11

bathroom door design options after do-it-yourself renovation, example 12

So, we examined the features of the restoration of the old door in the house on our own. We got ideas from looking at photos of finished ideas. We learned how to properly prepare the surface of the door for renovation.

If you feel the potential, but don't have the courage to take a swing at the big door, start with dollhouse elements. Your child will appreciate creative solutions for decorating doors, and you will have the courage to realize your desires to update them in your home.

Video: how and how to update old interior doors?

For equipment doorways bathrooms use products made of solid wood, chipboard or plastic. Operation of these products in high humidity conditions adversely affects appearance canvases. It is not easy to dismantle the old structure and install a new one, given the current cost of a quality door. Therefore, many people have a question, how to finish the inner door in the bathroom.

Preparing the door leaf for restoration

Before proceeding to the restoration, it is recommended to familiarize yourself with the stages of this work.

There are many ways to update the surface of the door leaf, but regardless of the choice, first of all, you will need to prepare a list of tools:

Building hair dryer;
Plane;
Putty knife;
polished machine;
Sandpaper.

The first stage of work is to process and clean the canvas from the old coating.

Important! Removal of the old coating will be required regardless of what type of finish is planned in the future.

Restoration work begins with the removal of the door from its hinges.

Removing the canvas from the hinges

The removed sash is laid on a previously prepared surface. The place for the restoration of the product is chosen so that it is well lit and ventilated.

All elements are removed from the door so that a bare canvas remains. If there are glass inserts, they must also be carefully removed. After cleaning the canvas from unnecessary elements, they begin to remove the old coating.

You can remove old paint in a variety of ways:

If the canvas has a thin layer of paint, it is advisable to use a special wash, which is a chemical agent that contains acid. This method is considered the most gentle. A wash with a brush is applied to the door covering and wait a certain time indicated in the instructions for use. Soon the old coating will swell, after which it is removed with a spatula.

The chemical solution is applied to the old paint with a brush or roller

Important! When applied chemical agent to clean the surface of the canvas, keep hands and eyes away from the product.

When many layers of paint have already been applied to the canvas, a lot of effort will have to be made. In such cases, a special hair dryer is used. Under the influence of hot air, the coating will swell, after which it is also removed with a spatula. This method is quite effective, but sometimes, due to imprudent work, the surface of the door can be damaged.

Removing old paint with a spatula using a building hair dryer

If there is no building hair dryer, you can use another method. Put a damp hard cotton cloth on the door leaf and press down with a heated iron. After two minutes, remove the rag and iron, and clean off the paint with a spatula. This procedure is quite laborious, and with its help it is difficult to clean uneven places on the canvas from paint. At the same time, the fabric and the surface of the iron quickly get dirty, which will also have to be cleaned.

Door leaf renewal

The particles of the old coating remaining after cleaning are removed with sandpaper. First you need to walk along the door leaf with coarse-grained sandpaper, gradually moving to the “zero”.

Important! Grinding work is carried out along the fibers to avoid the formation of transverse lines.

Sanding grinder

After grinding, the canvas is inspected for the presence of various defects. Small cracks are eliminated with putty. Large indentations are more difficult to eliminate. In most cases, to eliminate large defects in the canvas, you will have to cut out the damaged fragment and prepare an overlay from wood. It is adjusted in size and attached to the canvas with glue. Putty is also used to eliminate minor gaps resulting from gluing.

With a lacquered door, all manipulations from removing the old top layer are identical. Only one point differs - the choice of putty must be approached with special responsibility. Since the varnish is transparent, any flaws will be visible under it. The color of the canvas can be changed with varnish or stain.

Important! Internal laminated or veneered structures must not be painted. For their restoration, completely different methods are used.

Designs of this kind can be updated with a special wax pencil.

Wax pencil, photo

The pencil is first heated, after which all scratches and cracks are treated. The main thing is to choose the right tone of the pencil for the color of the door. If the material is chosen correctly, in this case, all processed errors will become almost imperceptible.

Choice of decor

The second stage is the direct choice of the type of decoration that will be applied next.

Coloring

The easiest way to update an old door is to paint it. But, given the features of the bathroom, you need to choose the right paint. It must be resistant to excessive humidity, temperature changes and not be afraid of frequent cleaning.

Painting MDF doors, a photo

What paint is suitable for the bathroom door

The range of paint is small, these are alkyd or acrylic compounds.

Advantages of alkyd paint:

Ideal for painting canvases made of MDF and chipboard;
available;
Protects well from moisture;
Not afraid of frequent washing;
Has an extensive color palette.

Disadvantages of alkyd paint:

Professionals do not recommend using paint for natural wood structures.

Important! Wood has the ability to "breathe", and alkyd compounds are vapor-tight.

This kind of coating exfoliates rather quickly, as a result, cracks appear on the surface.

The smell of paint does not disappear for a long time.

Advantages of acrylic paint:

Surpasses alkyd paints in terms of service life;
Not afraid of temperature changes and humidity;
Easy to clean;
There is no strong smell. There are compositions and completely odorless.

Disadvantages:

Despite the speed of drying paint, it remains susceptible to the slightest damage within a month.

Which paint do you prefer: glossy or matte?

Concerning the choice of the type of paint among professionals, disputes have not subsided for a long time. By their own decorative properties paints are divided into the following types:

Matte;
glossy;
Satin;
Semi-gloss;
Semi-matte.

The matte surface is the most unstable. This type of paint is completely unsuitable for covering door panels located in bathrooms due to high humidity. Glossy paint is also not quite suitable for the bathroom, because it has an excessive shine.

Door leaf painting, photo

Important! If the gloss of the canvas does not bother, then it is quite possible to apply this type of bathroom paint. Since from a practical point of view, gloss becomes the best option. The smooth surface does not absorb dirt and is less prone to stains.

Semi-gloss and satin paints are an average and versatile option.

After determining the type of paint, you can proceed to the direct painting of the door leaf. The key rule is the wise choice of color, as the painted door must be combined with the elements of the bathroom. Apply paint to any convenient way in 2-3 layers.

Another option for door restoration is a combination of several colors. First, the canvas is covered with one color. After drying, it is processed with sandpaper, and a second shade is applied. You can create the desired texture with the help of graters. After the canvas dries, it is varnished. Finished in this way, the door will acquire a new life.

How to restore doors from chipboard

This kind of material is not resistant to high humidity, so it is recommended to approach the restoration procedure responsibly. For this kind of material, you should not use a hair dryer, sandpaper for grinding, as this is fraught with surface deformation.

To remove the top layer of paint, you will have to resort to the "grandfather" method (iron and cloth) or apply a wash. With a spatula, the paint layer is very carefully removed to avoid damaging the canvas.

Grinding is done only by "zero". After gentle manipulations, paint can be applied.

Important! The best option for updating a chipboard structure is veneer gluing.

Choosing the right paint is an important, but the last step in the restoration of the structure. Equally important is accurate coloring, which is quite difficult to do without certain skills.

In contact with

Comments

Unfortunately, there are no comments or reviews yet, but you can leave your own ...

New Articles

New comments

S.A.

Grade

Svetlana

Grade

Sergey

Grade

Sergey

Grade

Alexei

All items in the house sooner or later grow old, acquiring an unattractive appearance. But if the furniture can be easily replaced, and the wallpaper can be re-pasted, then what to do with the doors? They are not so cheap to dismantle and buy new ones. Let's face it, given the cost of other things during the renovation, this part is not something you want to mess around with for a long time. To avoid this, you can decorate old doors with your own hands, which, thanks to the large number of options, often turns into an exciting activity.

1. Painting

The best way to freshen up an old door by slightly changing the design of the room is to paint it in a new color. In this case, you can use either one or several shades, highlighting, for example, panel parts, moldings or a frame.

Depending on the size of the room, the door can be a highlight or blend in with the wall decoration without dividing the space. The latter option is suitable for small spaces. In such cases, give preference to light colors.

It is recommended to purchase acrylic paint that does not leave odors, is evenly applied and does not harm health, which is important for a bedroom or nursery. But first you need to prepare your "canvas": even several layers of paint will not hide the bumps of the old wood. In some cases, for this you will have to remove the doors in order to correct all the shortcomings as much as possible.

Since it is necessary to work with a wide area, the method of application plays great importance to create a neat final look. Mentally divide the product into several small sections, evenly painting over them with even horizontal or vertical stripes. When dealing with paneled doors, cover them in the following sequence: insertion points, central strips, sides.

After complete drying, you can cover the surface with a protective varnish so that the updated door lasts even longer.

Solid colors will suit many styles not because of their neutrality, but because of the conciseness, restraint and simplicity that are relevant in modern interior design. You can follow fashion without large investments or experienced craftsmen.

2. Drawings and stickers

If monotonous decor is not your option, feel free to take a brush in your hands and paint your boring old door with interesting stories. People with artistic education can use it as a canvas, decorating with still lifes, landscapes, cartoon characters. For the rest, there are stencils or vinyl stickers- at least effective tools which will also provide a beautiful result.

In the case of stencils, the principle of operation is the same as in the first paragraph: we prepare the product, apply paint, and wait for it to dry. A painted or “bare”, pre-treated surface can serve as a basis. Pictures on the texture of old wood look spectacular.

3. Decoupage

This is an amazing method that, with all the simplicity of materials and ease of application, allows you to create real works of art. Decoupage is ideal for creating and decorating doors in the Provence style. Especially if you combine it with cracking varnish, which helps to visually age objects. Floral ornaments made in this way look very sophisticated and natural, making it possible to doubt the “home” origin of the decor.

So, you will need: PVA glue, napkins, sponge, scissors to cut out the necessary details of the picture. Paper is applied to the surface previously cleaned of dust and dirt, after which glue is applied to it. To avoid the appearance of wrinkles or bubbles, you can smooth the picture with a sponge by removing excess liquid.

After the door dries, and you have to wait about a day, the drawing must be fixed with ordinary furniture varnish. Almost any material can be decorated in this way, but it is best combined with wood.

4. Wallpaper

It can be a shame when after the repair there are several meters of unused wallpaper. Do not throw away - better leave them to decorate old doors! This is a completely inexpensive solution that will refresh the interior and hide the flaws of the product.

They can cover the entire area or individual details - it all depends on the image, as well as the design of the room. Some types of wallpaper have a relief structure, making the decor richer and more diverse.

For a nursery or a bright interior, you can take photo wallpapers depicting landscapes, paintings or other doors. Small games with perspective will visually enlarge the space. Only the rest of its elements should balance the composition, being a neutral background.

5. Fabric

For the decoration of old doors, you can take the remnants of fabric, especially if they were used for furniture upholstery. Such an intersection of patterns will look appropriate in one interior.

In any case, fabric is a textural, eye-catching solution that will definitely help freshen up an old item while covering minor flaws. You can fix it on the door using ordinary glue or furniture clips. The second option is good because over time, a boring part can be removed.

Lace is popular not only in clothing, but also in decor. Here, with their help, you can emphasize the refined taste of the owners by decorating the door with them.

6. Skin

A leather-covered door is certainly a sign of the status of the owners. It will fit more into the space of an office than a nursery, but because of this, it becomes no less interesting as an option for decor.

According to the rules, of course, such products must be ordered in salons, always from natural materials. But for a less solid interior, a substitute is quite suitable, since it can be chosen in all possible color combinations.

For the skin, you will need rivets that will help it beautifully “fit” the door and fix it. In addition, it can give the design an industrial touch that fits perfectly with the style of the loft.

Fine carving on the skin or drawing will look luxurious. Another one original idea: a door trimmed with old belts, but for this you will have to visit more than one flea market.

7. Mosaic

Mosaic compositions will never lose their relevance: they are beautiful, unusual and interesting to implement. Something like a puzzle, only you come up with a picture yourself.

You can use ceramic, glass or acrylic parts. Make sure that all the colors for the future "picture" are enough. These can be realistic stories, surrealism, or randomly arranged elements that are fixed with ordinary glue.

You can decorate the facade, panel or doorway. Check the reliability of the product so that when the doors are closed suddenly, some part does not suddenly fall off.

8. Aging

For some styles, the presence of elements literally saturated with history is the main condition. But here it is worth distinguishing between "shabby" and "luxurious" old age. We need a second view, and we will have to work on creating it.

There are many ways to artificially age furniture. Some of them are professional and not feasible under normal conditions. Others are simple tricks that successfully mimic cracked paint.

For decorating doors, you can use craquelure varnish, which literally makes the paint crack. Do not forget that it is better to work with several layers - to give more depth to the drawings.

A dry brush also does its job perfectly, which briefly paints the surface, giving it a worn look.

Several layers of paint can be rubbed with sandpaper, revealing the layering of the coating. And if you rub a wax candle in some places, paint the door and rub it, then the paint will fall off locally, also creating the desired effect.

9. Stained glass

Multi-colored stained-glass windows in temples, smoothly letting in light, always arouse admiration from the audience. Why not try to create a faint but similarity of this beauty at home, at the same time decorating old doors?

For this method, glass inserts are used. And here you have two options: buy a finished product with a pattern or decorate it yourself. The latter, of course, is more interesting, but it can be done after some preparation.

Apart from acrylic paints, with which the drawing is applied, you will need a special contour that creates the illusion metal frame. The glass sheet must be in a horizontal position so that the paint does not flow down the slippery surface without having time to grab. The finished product must be installed in the panel and fixed with glazing beads.

10. Molding

Moldings will also help to decorate old doors - elements that imitate stucco molding, which is so relevant in classic interior or art deco style.

Parts are usually made of foam or polyurethane, and therefore cheap, but allow for truly luxurious designs. You can buy ready-made components, fix them on the door with liquid nails or glue.

Usually, door decor with moldings is not very diverse, but sometimes it turns out to stumble upon aesthetic models. They can be painted in a color that intersects or contrasts with the main finish, achieving different effects.

Video: How to decorate a door - DIY decor

Let's look at a few of the most simple ways do the decor of interior doors with your own hands using improvised materials.

As you know, doors are not eternal, and anything can happen. For example, often scratches, chips, cracks appear on the door leaf. In this case, you can repair, replace or decorate carefully, hiding all defects.

Covering the door with wallpaper

To decorate the door, you can use not only paper, vinyl and non-woven wallpaper, but also fabric or liquid.

In this case, the canvas should be prepared by removing a layer of paint in advance, filling irregularities, cracks and sanding the surface.

The applied primer layer will provide additional adhesion of the wallpaper to the door surface.

Wallpaper can be pasted over both the entire canvas and the panels, cutting out pieces of wallpaper of a suitable size. Don't forget to choose the glue that suits the type of wallpaper and dilute it according to the instructions.

Wallpaper classic

Lubricate the cut wallpaper with glue and apply it to the door, making sure that there are no jams and distortions. Smoothing the wallpaper soft cloth, roller or wide plastic spatula. Carefully cut off the excess with a clerical knife. Additionally, you can decorate by gluing a foam plinth frame over the wallpaper.

For the period of drying of the wallpaper, it is advisable to close the windows in the house and exclude the appearance of drafts, a sharp temperature drop.

Textile

The door decorated with fabric looks very unusual and attractive. In addition to the standard surface preparation, attention should be paid to the fabric itself, ascertaining the degree of shrinkage.

We cut off a small piece of fabric, measure its dimensions, moisten it with water and dry it. After drying, we again take measurements, comparing the readings and finding out the degree of shrinkage. If the value is large, then we also wet the entire piece of fabric before decorating and leave it to dry.

Note! You can use not only a single piece of fabric, but also cut fragments different color and invoices. This technique is called "patchwork" and is often used by designers in the design of premises.

For fabric, casein glue, a composition based on CMC, as well as Bustilat or Gumilaks mastics are best suited. We apply the adhesive to the fabric and apply it to the door, smoothing it with a spatula. When pasting the door with fragments, it is important to monitor their geometry, otherwise the work will look sloppy.

Additionally, you can decorate the door with beautiful furniture carnations, shiny nylon or leather cords, fabric paint, baguette frames.

- are universal. They cover not only walls, but also doors, creating unimaginable patterns and compositions. In this case, you do not have to mess with cutting canvases. However, it will not be possible to expose the door to moisture. Therefore, for decorating a door in a bathroom or kitchen, this method is unacceptable.

To work, you will need a dry wallpaper mix, several spatulas of different sizes, a hopper gun, a roller, a clear varnish, a color scheme.

Decorate the door with a mirror

A very unusual door finish can be made using mirrors. Such decor will not only attract everyone's attention, but also visually expand the space of the room, add light. However, cutting and attaching a classic glass mirror is very inconvenient, since there is an alternative - acrylic panels with amalgam, which has excellent reflectivity.

Acrylic mirrors are available in a wide range color scheme. You can choose any shade you like or several to make a mirror panel. Plastic panels do not break, are easily processed and attached to the door, and are light in weight. The cost of mirrored plexiglass is not the lowest, but the quality and aesthetic qualities are fully consistent with the declared prices.

Thickness	Colour	Trademark	Sheet size, mm	Price per sheet, rub
2	silver	SPD (Italy)	1220*2440	5950
2	silver	Plexiglas Mirror (Germany)	2050*3050	11150
3	silver	PLASKOLITE (USA)	2050*3050	14000
3	gold	PLASKOLITE (USA)	2030*3050	15700
3	gold	Plexiglas Mirror (Germany)	2030*3050	16000
3	red, blue, green, orange, yellow, black (colored opaque)	Extruded acrylic glass ZENOCRYL OPAQUE XT	2050*3050	10989
3	color transparent (red, orange, yellow, light blue, blue, green, violet)		1220*2440	5453
3	fluorescent transparent (yellow, pink, brown)	Cast acrylic glass ZENOCRYL TRANSPARENT	1220*2440	5075

Before attaching the mirror plastic to, you should carefully level the surface by deepening the nail heads, sanding and covering all the bumps / recesses with putty.

A primer must be applied to the door and the back of the acrylic sheet deep penetration. After it dries, the cut panels are fixed with double-sided tape and mounting glue. For convenience, use mounting suction cups, with their help it is much easier to carefully glue the panels to the door leaf.

As one of the decoration options, you can consider figured acrylic mirrors. Such a mirror can be attached in the center of the door or you can purchase several elements and arrange them beautifully. Usually small parts are produced with an adhesive layer already applied.

Even from this simple material, as buckwheat husk, excellent work is obtained. The cost of the material is minimal, but the service life of such a coating, unfortunately, cannot be called too long.

Step 1. Remove a layer of old paint from the door, the existing vinyl coating, eliminate all irregularities with putty.

Step 2. Remove the door from the hinges and put it on the floor / stools / table. We paint the door leaf with dark brown paint. If there are glass inserts on the door, we protect them with masking tape.

Step 3. We thickly grease the dried door with PVA glue, lay out the husk, distributing it with our hands. If necessary, add small gold sparkles.

Step 4. We cover the door with a transparent varnish (glossy or matte). It is advisable to apply three layers in order to qualitatively fix the buckwheat on the door leaf.

A beautiful door is ready. So that the door does not stand out from the overall design of the room, decorate the picture frame in the same way and place the creation on one of the walls.

We decorate the door in vintage style

Vintage is sophistication and sophistication, the beauty of artificially aged things, in harmony with the chic of individual decorative elements. The door in vintage style will become a work of art, an exclusive element of the interior.

For decoration you will need:

We will combine door painting with decoupage technique and add decorative elements in addition. We will carry out the work on the already removed from the hinges, puttied and carefully sanded door, laid horizontally.

Step 1. Paint the door white. We apply the paint with a wide brush with stiff bristles in one direction, in a thin layer.

Step 2. When the paint dries, gently sand it with coarse sandpaper, achieving the effect of "old times".

Step 3. We start decorating the panels or the central part of the door. We tear musical notebooks and old newspapers into small pieces with our hands. We draw a field for activity of a rectangular or square shape on the door with a pencil. Lubricate the outlined areas with PVA glue. Immediately lay out the paper randomly, smoothing it with your hands. On top, apply a transparent varnish in two layers.

Step 4. Along the perimeter of the areas pasted over with paper, we fasten a black baguette to the mounting glue.

Additionally, you can decorate with a beautiful wreath, a large lace bow or plastic beads imitating pearls (glue-based).

There are many other ways to decorate doors. Operate with the materials available in your home arsenal, connect your imagination and create your own masterpieces.

Entrance door prices

Entrance doors

Video - A variety of ideas for decorating doors

Video - Applying patina to the door

Video - Self-decorating the door

11 best manufacturers of interior doors

	Name	Rating
#1	EL "PORTA	⭐ 100 / 100
#2	TRIADOORS	⭐ 99 / 100
#3	STATUS	⭐ 98 / 100
#4	SOFIA	⭐ 97 / 100
#5	ART DECO	⭐ 96 / 100 1 - voice
#6	PROFILDOORS	⭐ 95 / 100
#7	ONYX	⭐ 94 / 100
#8	BELWOODDOORS	⭐ 93 / 100
#9	MATADOR	⭐ 92 / 100
#10	VOLHOVETS	⭐ 91 / 100
#11	ALVERO	⭐ 90 / 100

Doors el'PORTA

Doors el'PORTA are doors with Italian architecture, produced in Russia. Models modern design and trendy shades, materials of the highest quality. el'PORTA interior doors are manufactured using modern Italian and German equipment. Various decorative coatings doors allow you to choose best option in terms of price and performance.

Doors EL'PORTA

Characteristics:

3D-Graf - Structural decorative material increased density. It has a pronounced texture, medium wear resistance;
eco-veneer is an anti-vandal decorative material that imitates a cut of a real tree. High wear resistance, resistance to mechanical damage, fading, moderate resistance to moisture;
aqua doors - doors that are not afraid of moisture;
enamel - a multilayer material that imitates enamel, but has higher.

Doors EL'PORTA

- each product is an effective combination of priorities modern materials, trouble-free fittings, successful structural and design solutions. Such doors are very appropriate in rooms decorated in modern high-tech or minimalist styles.

Characteristics:

contemporary innovative coating Renolit (Germany) stands out for its strength, durability and environmental safety;
carelessness. It is enough to wash it occasionally with ordinary furniture care products (not containing abrasives);
doors can be installed in any room, even with high humidity;
easy to use, as well as durable and reliable.

— Stylish minimalist design will appeal to the modern city dweller. A rich choice of textures and finishes allows you to harmoniously fit these doors into a new, as well as into an already finished interior. Telescopic door trim- this is a constructive solution of the door frame, which allows you to fit to the wall of any thickness.

Characteristics:

due to the telescopic effect, the design is suitable for walls of any thickness. Thanks to a tighter fit to the wall, the box does not warp over time;
harmless material based on polypropylene;
a jointed massif of Angarsk pine is used in order to ensure the stability of the frame, low weight of the canvas, as well as environmental safety consumers.

— Sofya doors are an author's design product, impeccable European quality and operational service. Factory "Sofya" performs a full cycle of product creation from the development of the design of each door collection with Italian designers, the development of manufacturing technologies with German engineers.

Characteristics:

door painting based on safe acrylic-based components used in the medical industry;
absolute precision in the execution of all joints in the most unusual collections;
careful selection and research of the materials used;
ecological, strong and durable in operation.

— direction Design by ARTDEKO is interior doors for true connoisseurs of beauty and comfort. warm shades natural wood, exquisite forms, luxurious decor of classic doors will become a real decoration of the interior. Manufacturability and concise forms of doors in modern style— an example of high design for adherents of minimalism.

Characteristics:

veneer is used from valuable wood species such as oak or ash;
inserts made of transparent, frosted, colored or patterned glass;
are made on high-tech equipment by qualified specialists using high-quality raw materials and materials.

- this type of door structure is a collapsible structure of individual elements (tsarg). The main advantages of this design is its high maintainability, due to the ability to replace any part of the door during operation and a huge range of different models, both in modern and classic style.

Characteristics:

resistance to chemical and physical influences;
a feature of the coating is its pronounced deep “brushed” structure with a glossy lacquer monochromatic surface or a matte lacquer monochromatic surface;
Complete with German Simonswerk hinges and German KFV lock.