Baths

Is it possible to lay marmoleum on old linoleum. Marmoleum - characteristics, styling technology, photo

In one of the previous articles, we have already considered the features of such finishing material as marmoleum and clarified all its advantages and disadvantages. Today we would like to acquaint the reader with the procedure for laying the presented flooring and reveal the nuances of the work.

Preparation for work

As mentioned earlier, marmoleum is identical in its visual characteristics to ordinary linoleum, but unlike it, it is produced not only in the form of rolls, but is also made in the form of tiles (like PVC) or panels with a lock connection (similar to laminate). In view of this, laying marmoleum with your own hands is somewhat different depending on the material used.

Foundation preparation process

Depends on the base material. So, if you plan to lay marmoleum on wooden surfaces, then you should first make sure of the mechanical strength of the base (damaged floorboards, cracks, drops are not allowed). And after that, make the final leveling of the floor by sheathing it with OSB panels or plywood sheets.

When it is planned to lay marmoleum on a concrete floor, you should make sure that there are no potholes, cracks, chips and, if necessary, level the base with a cement-sand mortar or self-leveling mixture.

In addition to the procedure for preparing the foundation for initial stage it is advisable to mark and cut the material. Why panels or tiles need to be laid out at the place of intended installation and mark control points.

When performing these operations, it is necessary to take into account certain features:

Marmoleum belongs to the group of natural finishing materials, which is why it has the ability to change linear dimensions with temperature changes. That is, when laying it, it is necessary to provide for compensation gaps between the material and the wall (10 - 15 mm), which will subsequently be covered with a finishing plinth.

Mechanical processing of marmoleum (cutting) is associated with certain difficulties, which is why in the process of work it is desirable to minimize the number of cuts as much as possible and place them in visually hidden places.

Marmoleum laying technology

Depending on the type of material used (rolls, tiles or panels), the method of laying the material also varies.

Rolled marmoleum is laid by analogy with linoleum, however, unlike the synthetic counterpart, marmoleum is not allowed to be rolled up more than 1 time, and this can only be done with the face up. This circumstance is connected with the fragility of the finish, in particular its end zones. That is, the material is simply rolled out in the room and it is trimmed around the perimeter, after which the matured marmoleum is pressed to the floor with the help of skirting boards and decorative thresholds.

Marmoleum in the form of tiles (50x50cm, 30x30cm) can be laid using two methods: with and without pattern selection. Moreover, in the first case, the installation of the finishing material should begin from the middle of the room, gradually moving to its edges. Whereas in the second option (for standard-shaped rooms), it is best to start laying from the wall, with the smallest dimensions.

The very algorithm of the work involves the following actions:

At the place of laying the first row (near the wall), a base rail is set - a beacon (10 - 15 mm thick);
A specialized adhesive composition is applied (in the form of a snake) to the wrong side of the finishing material;
The tile is matched with the beacon rail and simultaneously pressed against the base base;
All tiles of the first row are laid in the same way, after which the whole process is repeated again (until the work is completed);
After the adhesive has dried, the inter-joint voids can be filled with a special grout of the appropriate color shade.

Panel marmoleum is laid by analogy with a standard laminate. However, unlike this material, the joining of marmoleum panels is more difficult, due to its flexibility and fragility. Therefore, adjacent elements should be connected at a strictly defined angle, due to which the most high-quality engagement of the floorboards is ensured.

To ensure a given angle of inclination, it is best to use wooden templates with an oblique cut (the angle of inclination of which will allow the marmoleum panels to be positioned at the most optimal angle during installation).

Such equipment is placed under the free edge of the trim and fixed in the groove of the previous row. Well, in order for the adjacent panel to close, the bar is simply removed and the marmoleum takes the desired position.

In order for the installation of a natural floor finish to not cause any particular difficulties, it is advisable to follow some recommendations in the process of performing work:

Tapping marmoleum (for high-quality joining) must be performed through special spacers and using rubber hammers.
For cutting marmoleum, it is best to use a hacksaw or a jigsaw with an appropriate file (fine tooth, reverse direction).
Marmoleum should be purchased only in specialized shopping malls guaranteeing the originality of the product.
In order to ensure a good fit of the material from the base bases, it is necessary to remove all dust and construction debris in advance with a vacuum cleaner.

01.07.2017

Every year the construction market pleases with a mass of new materials. One of these is marmoleum. This material is used for laying as a floor covering and cannot be used for any other purpose.

What is a material?

The presented product looks very similar to ordinary linoleum, but it differs in its technical characteristics.

Marmoleum has main feature: It is a completely natural material.

The fact is that the following components are used for manufacturing in production: linseed oil, chalk, resin of coniferous trees, wood flour, as well as elements of cork oak wood. The use of various dyes allows you to get a lot of color and texture options.

Another feature of the product is that the pattern on its surface can retain its brightness and colorfulness for a long time. This is ensured by a special technology for applying a picture, which involves its location throughout the entire thickness of the layer. In stores, marmoleum is sold in the form of panels, rolls, and tiles. The roll version is the most common.

Specifications

Before purchasing this natural material, you need to find out what features it has. Marmoleum has the following technical characteristics:

Guarantee period operation: at least 35 years.
Mechanical strength of the product: 160 kg/cm2.
Standard dimensions of the material: roll - width - 2 m, thickness - 2-4 mm; tiles - 50x50 or 30x30 cm; panels - 90x30 cm.
Specific gravity: 2.6-3.4 kg/m2.

Classification

Such flooring has a classification similar to linoleum. For example, there are such classes of marmoleum:

41-43 - such a product can be considered the most durable and reliable. It is used most often where a large number of people accumulate. For example, this material can be laid in shopping centers, airports, train stations. Due to the thickness of the decorative layer, which is 3 mm, it can serve for a long time and with high quality.

Pros and cons

Marmoleum has the following advantages:

Safety. Since the product is made from natural materials, it does not emit any harmful substances. In addition, such a coating is well suited for allergy sufferers and children. Natural resins, which are present in the composition of the material, provide a bactericidal effect.
High degree of resistance to mechanical stress.
The product tolerates UV rays well, so it does not fade.
The coating has high level resistance to fire and temperature changes. This feature allows you to use it for arranging underfloor heating.

Moisture resistant.
Despite the relatively small thickness of the layer, such a floor does not require additional noise, thermal and waterproofing. Thanks to this, your repair will be completed faster, and you will spend much less money.
Large variety of sizes.
Possibility of laying the material on the old flooring.
Resistance to the influence of chemicals.
Good decorative quality.

And this material practically does not accumulate static electricity.

Despite the fact that this coating is natural, it also has certain disadvantages:

Relative hardness. Over time, the coating spreads a little and hardens. This fact does not allow it to be used for decorating walls or ceilings.
Fragility. During transportation and use of the product, you need to be especially careful with the edges of the elements. As for the rolls, they can only be rolled up once.
Enough big weight. But this does not prevent marmoleum from remaining relatively plastic along the edges.
Difficulties in processing. When cutting elements, you will not be able to achieve a perfectly even and smooth cut. However, this problem is eliminated by installing a plinth.

Features of laying roll coating and panels

The presented flooring has enough good feedback users to help you choose suitable option. Now you can consider how the marmoleum is laid. First of all, it needs to be prepared for work. That is, a roll or tile should lie down in the room in which they will be laid for at least a day. During this time, you can remove all furniture, debris from the room and vacuum the base well. You may need to further align it.

In principle, rolled marmoleum flooring is most often produced in large rooms. The technology of its installation is practically no different from the installation features of conventional linoleum.

As for the panels, they must be laid as carefully as possible. The fact is that the fastening latches are thin spikes that can be broken with one inaccurate movement.

Features of mounting tiles "click"

The presented material is laid on the substrate. It compensates for some unevenness of the base, and also prevents the formation of condensate. Typically, such a substrate is made of polyethylene, and is laid with a slight overlap of 20 cm. An additional layer of thermal insulation is not needed. Please note that you do not need to use glue to mount the elements.

So, the coating laying technology consists of the following stages:

Installation of the first row. When doing this, keep in mind that you will have to step back from the wall by about 1 cm. This is necessary for the formation of expansion joints. The groove of the first element should be directed in the opposite direction from the wall, the ridge, on the contrary, should be directed towards the wall. Marmoleum is mounted quite simply, but this process has a peculiarity: each subsequent tile must be connected to the previous one at a slight slope.

In the photo - the same installation feature. Docking of the next tile is made at an angle.

Installation of the second row. It is made in the same way as the previous one. Remember about the expansion joint, for this, put a bar under the first tile. After attaching the remaining elements, it is removed, and the locks snap into place.
Installation of the remaining rows. In this case, parallelism must be taken into account.

Strange, but the further science advances in terms of creating cheap artificial materials, the more people tend to use natural materials in decorating their homes. Not everyone can afford a complete decoration of an apartment or house with natural building materials, but you still want to bring at least something to your home.

One of the available natural materials is marmoleum, which is also called "natural linoleum". Its cost is about 2 to 3 times higher than the cost of a quality one, but it is quite affordable for most people.

Do not think that marmoleum is a super-modern material. Its prototype was invented in the 16th century. And now the production process is simply improved, thanks to the capabilities of modern technology.

Marmoleum - what is it

Let's start with the fact that only natural ingredients are used in the manufacture of the material:

wood flour;
linseed oil;
resins of coniferous trees;
natural coloring pigments.

Thanks to the variety of natural dyes, manufacturers have managed to create a material of such a wide range of colors that the decoration of each interior can be made exclusive.

The color pattern of marmoleum is carried out over the entire thickness of the material, therefore, even with some wear, it retains its decorative effect.

Part of the cost of the material is due to the duration of the process of its production:

linoleum mass mixed from natural products should mature within a week at a certain temperature;
after that, pigments are added to it and pressed on special machines;
then the layer is cut into strips of a given width and laid on a jute base;
the resulting dense texture matures for another two weeks in the drying chamber, where it turns into marmoleum;
the last step is the creation of a protective surface layer of polymers that increases the wear resistance of the coating (you can purchase material without this layer, it will be 100% natural, but it must be constantly rubbed with special mastics).

The quality of the material and its types

Like many floor coverings, marmoleum is divided into classes in terms of quality and durability:

22 - 23 class - the thickness of the pattern is about 2 mm, the coating is used for laying in general purposes (including residential);
31-32 class - the thickness of the pattern is 2.5 mm, the coating can withstand significant loads and has an industrial application;
41 - 43 class - the thickness of the pattern is at least 3 mm, the coating is used in rooms with high traffic (airports, hotels).

The higher the class of coverage, the higher its price. Therefore, when buying marmoleum for the home, you should not overpay for quality, the thinnest and cheapest material is quite suitable here.

Depending on the form in which it is released, marmoleum is divided into:

roll width 200 cm;
square tiles with dimensions of 30*30 and 50*50 cm based on HDF board;
rectangular slabs with dimensions of 90 * 30 cm.

For home use, tile material is more often bought, which is less susceptible to damage, both during transportation and during installation.

Advantages and disadvantages of marmoleum

Disadvantages, like any, there are, but they are few:

Many advantages:

Environmental friendliness of the material, making it possible to use it even in medical and children's institutions;
, which gives it the resin of coniferous trees;
Hypoallergenic for both people and pets;
Large selection of colors and shades wide opportunities design;
Simple and quick installation of the coating;
Possibility of reuse with careful dismantling of tiled coatings;
High, unlike linoleum, resistance to mechanical damage and chemicals;
Marmoleum tolerates well high temperatures, so it can be used as a top coat for .

To begin with, it is worth noting that the material is not recommended for flooring in damp or cold rooms.

The best conditions for its operation are: humidity not more than 60% and temperature not lower than 18 degrees. Therefore, bathrooms are contraindications, where the coating can be deformed and unheated rooms ( summer houses, and loggias).

The material is good for floors in children's rooms, bedrooms, living rooms, office spaces.

Preparing for styling

First you need to carefully examine the purchased material in daylight. If you find defects after installation, you will no longer be able to claim quality.

Before starting work, the packages with the material are stored for 2-3 days in the room where it will be installed, laid on a flat surface.

The room must be dry and clean, all concrete and plastering work and installation of windows and doors.

The subfloor must be level, dry and solid. If there are irregularities, they must be eliminated using a self-leveling floor or a dry screed. The deviation of the surface from the horizontal can be no more than 2 mm in either direction per 2 m.

Humidity concrete base cannot exceed 2%.

As you can use a polyethylene film with a thickness of 0.2 mm. The edges of the film must be brought to the walls by 5 cm, and overlap at the seams by at least 20 cm.

For better sound insulation and impact noise cut-off, a special polyethylene foam underlay with a density of at least 30 kg / cubic meter should be laid on top of the waterproofing. m and 2 mm thick.

If you have chosen roll material, then its installation is practically the same as. The only limitation is to avoid bending the material too much, it can crack.

For laying tiles you will need:

roulette;
marking pencil;
or ;
wedges 1 - 1.5 cm thick;
wooden bars;
a hammer.

Determine in advance the pattern of the floor, the direction of laying the tiles. Carefully examine the places where pipes pass, the location of thresholds, wall protrusions and decide on the most rational placement of tiles in these places.

Technology:

The gap between the wall and the first panel should be at least 1-1.5 cm, which will protect the floor from deformation during thermal expansion. Prepared wedges are used to set this gap. The first panel is laid with a ridge against the wall, the rest are butted up to the end of the row. You need to adjust the position of the panel by gently tapping the gasket from a wooden block with a hammer. This precaution will help avoid damage to the material.
The beginning of the second row is the cut of the last plate of the first row. It is inserted with a spike into the groove of the first row, but the lock is not latched, leaving the panel at an angle. The slope is provided by prepared bars. All panels are sequentially butted together with ends, leaving them at an angle. And only when the whole row is ready, the bars are removed and by gently pressing the second row along the longitudinal joint they snap into place with the first.
All subsequent rows are mounted in the same way.
After laying several rows, if the distance between the marmoleum and the wall is less than 1 cm, the position of the coating is corrected.
If the width of the last row is less than the width of the tile, then the material is cut to width with a jigsaw.
Minimum clearances must also be observed near the pipes. At the end of the work and close with special overlays.
fasten only to the wall, since the coating should not be fixed motionless. The width of the plinth should cover the installation gap between the floor and the wall.
If the edge of any panel crumbled a little during installation, then at the end of the work all such defects are sealed with a compound for linoleum, it is only important to choose the right color.

Maintenance is easy:

According to consumer reviews, for some time after laying the coating in the room, there may be a smell of oil, which eventually disappears. You need to be prepared for this and not be afraid - marmoleum does not emit any hazards.

It was also noted that wood saws with a pitch of 2.5 mm make it possible to cut the plate material almost perfectly - without chips and scuffs.

When laying marmoleum in the kitchen (for greater sealing of the coating), sealant can be used to process the seams, the excess of which is easily removed 10-15 minutes after application.

Appeared not too long ago new material for finishing the floor marmoleum. What is it? Essentially, this natural linoleum, only much best quality. Their main difference lies in the fact that this material consists of natural and environmentally friendly components. It is made from resin needles, jute, cork, using linseed oil and natural dyes. This is undoubtedly a huge plus of this product. But before making a decision: apply marmoleum in the process of building and repairing with your own hands or not, you need to weigh the pros and cons.

2. Benefits of marmoleum coating.

The high strength of this material. Able to withstand a load equal to 160 kg per 1m 2. This means that even very heavy furniture does not push it to the point of dents.

The solvent and various other chemical solutions do no harm to the marmoleum.

Spilled liquids of various origins leave no traces and are easily removed from the surface. marmoleum.

This material is stained to its full depth, which ensures the preservation appearance even with gradual erasure.

Coating marmoleum has antibacterial properties due to the presence in its composition linseed oil.

Does not cause allergies.

It does not burn and is almost impossible to burn through, except at ultra-high temperatures.

Marmoleum refers to fairly good sound insulators.

Ecological purity of marmoleum.

Consists of natural ingredients.

3. Disadvantages of marmoleum coating

One of the main disadvantages of marmoleum is its fragility, especially at the edges.

Fairly heavy material. Again, this applies more to the roll type.

By the way, if you use such a marmoleum, then you need to contact the specialists, because it will be problematic to lay it with your own hands. Since this requires special equipment.

When cutting, uneven and ugly edges are obtained. But if, to cut off only those places that will then be covered with skirting boards, then there is no tragedy in this.

May deform over time due to spreading. Therefore, when buying, be sure to check the integrity of the packaging and the expiration date of the product!

First time off cover marmoleum comes out bad smell. However, it disappears after a while.

Such a floor will not be a cheap pleasure.

Now let's talk about how to produce laying marmoleum with your own hands. There is nothing complicated in this process. Naturally, we only mean marmoleum tiled (there are sizes of 30 × 30 or 50 × 50 cm) or panel type (90 × 30 cm in size). By the way, the technology itself is very similar to laying a cork floor, which we talked about how to lay.

Stages marmoleum laying:

1. To begin with, as always in the process of laying flooring with your own hands, you need to prepare its base. If the old floor is even, without depressions and potholes, then natural linoleum can be laid immediately without prior preparation. The main thing is that the surface is clean. If there are any irregularities and the floor is wooden, then it is usually leveled by covering it with plywood, OSB or something similar. If the floor is concrete, then you can pour a self-leveling screed. The most important thing is to ensure that the surface is even, in order to avoid damage to the material in the future.

2. Since the coating marmoleum has a tendency to deform due to temperature changes, namely, it becomes longer when it rises, and when lowered, it takes its shape again, you need to leave the so-called temperature gap around the entire perimeter of the room. As a rule, special spacers should be included in the kit for this. This gap will then be closed with a plinth.

Fig.1 Spacers when laying marmoleum

3. Marmoleum laying starts from the center if some pattern is provided. If not, we stack from any corner in order.

4. Joining plates natural linoleum takes place in a special castle. Since this is done at a certain angle, it will be convenient to use beveled bars for the stop, which are removed immediately after joining the plates.

Fig. 2 Bar covered with marmoleum

Fig.3 Bar

5. If you need to knock on the plates marmoleum, do it through some kind of spacer, and not directly on the material. As a percussion tool, use a rubber mallet or mallet.

Fig. 4 We knock the plate through the spacer

6. Trimming marmoleum is done with an electric jigsaw or a saw with a fine tooth.

Fig. 5 We cut the plate

5. To recap

In general, as you can see, there is nothing complicated in the process marmoleum laying with your own hands. The main thing is to level the floor and work carefully with the material. If you have any questions, write in the comments. good luck to you do-it-yourself construction and repair!

Natural linoleum (marmoleum) appeared in the 17th century, but for some time it was replaced by more affordable and practical linoleum. Currently, this flooring has again become popular and in demand.

What is marmoleum and how is it produced?

The material is produced by pressing a mixture of cork wood, lime, linseed oil, flour, jute fiber, coniferous tree bark, natural dyes.

In certain proportions, these components are mixed, kept for maturation and pressed under high pressure at elevated temperature. The result is a floor covering that can be safely called natural. Top material is covered protective layer, which makes it easy to care for, provides UV resistance and makes it even more durable.

Types of marmoleum

Depending on the thickness of the decorative layer, the material is produced thin (from 2 to 2.5 mm) and thick (from 2.5 to 4.0 mm). It can be based on chipboard (castle) and on a cork substrate (adhesive).

The lock-type coating resembles parquet board or laminate. It consists of three layers: the top layer 2–2.5 mm thick is, in fact, marmoleum, the middle layer is chipboard, the bottom is solid cork. The strength of the interlocks provides a very strong middle layer of chipboard high pressure(HDF).

It feels hard like laminate, warm like parquet (colder than cork but warmer than laminate). On the Russian market there is a material with a lock connection produced by the American concern FORBO.

Manufacturers offer three types of coverage:

Tiled

Tiles are made with a size of 300x300 mm or 500x500 mm. Tiles are laid like PVC or quartz vinyl, on glue.

Panel

Panels are longer than tiles. The size of the panels is 900x300, they are laid, like tiles, on glue.

rolled

Marmoleum sheets in rolls can have a thickness of 2–2.5 mm and 2.5–4 mm (thin and thick, respectively), a width of 1.5 to 6 m and a length of up to 32 m. The weight of one roll is about 120 kg. The rolls are heavy, the edges of the sheets are fragile, crumble easily, it can only be rolled out once.

Do-it-yourself laying roll material is not recommended. The basis for it is a layer of cork. We need a crane, a team of riggers, loaders. The rolled roll cannot be rolled up again, therefore it is better not to use rolled marmoleum in residential premises of a small area.

Wear classes

Like synthetic linoleum, marmoleum is produced in several classes of wear resistance:

21–23 thin (up to 2 mm) household, suitable for living conditions with a small load on the floor (bedrooms, offices).

31-33 2.5mm thick semi-commercial, static load-bearing, suitable for high traffic areas and floor loads.

41–43 layer thicknesses over 3.2 and 4 mm, suitable for floors subjected to intensive use, such as train stations, airports. It is also used in domestic conditions, but it is much more expensive than household one.

Advantages

Natural environmentally friendly material.
It has bactericidal properties, as it contains linseed oil.
The material is non-toxic, does not cause allergic reactions.
Resistant to solvents, acids and other chemicals.
Does not fade under the influence of sunlight.
Possesses antistatic, sound-proof properties.
It is not subject to deformations under mechanical stress, withstands loads up to 160 kg / cm 2, is easy to maintain, and is resistant to fire.
Great variety of colors, easy to install.
Service life more than 20 years.
The material is hard, but fragile at the edges, requires care in work.
Over time, it hardens and blurs, so the gaps are reduced.
New sheets have an unpleasant odor that disappears over time.
Heavy coating, along the layers has residual plasticity.
It is poorly cut with a knife, it is difficult to get a smooth edge.
Not suitable for underfloor heating, as it does not transmit heat well.
Not recommended in kitchens and bathrooms (manufacturer's recommendation), as the material may warp in high humidity. The optimum temperature is 18°C, humidity is not more than 60%.
Not recommended for use on unheated balconies and loggias.
Expensive coating in comparison with linoleum and laminate.

Flaws

Self-laying technology

The laying of the roll coating should be entrusted to professionals. The material is heavy, brittle, and may crumble at the edges.

It is better to mount tiles or panels on your own with or without a base. Laying marmoleum as a whole is not difficult if the base is even, and the layer does not forget about the fragility of the material. Tiles should be handled very carefully.

Laying marmoleum tiles or panels without a backing is like applying quartz, PVC or natural cork tiles, while installing HDF backed boards is similar to working with laminate with some subtleties.

Consider laying marmoleum on the basis and without it. The steps are:

Base leveling. This is the most important and crucial stage, since marmoleum is very sensitive to floor irregularities. The wooden floor is leveled with plywood or OSB sheets, it is better to level the concrete floor with a self-leveling screed. After that, the floor under the adhesive tiles should be treated with a deep penetration primer.
Temperature gaps of 1.5–2 cm are made along the perimeter of the room, inserting wooden planks wrapped with plastic wrap or liners (inserts are attached to the material, which are removed after laying the coating).
The laying of the lock panels is carried out according to the type of installation of the laminate, staggered: each subsequent row starts from the rest of the board of the previous row. If a pattern of tiles is supposed to be on the floor different color, it should first be depicted on paper and on the floor, and it is better to start work from the center of the room.
Connecting fragments due to its flexibility of the top layer presents some difficulty. Bars cut under a wedge with an angle of inclination, under which the fragment is inserted into the lock, will help to cope with the problem. The bars are substituted under the marmoleum and inserted into the groove of the previous row. Then the bars are removed, and the coating strip takes its position.
To cut boards, use a jigsaw with a metal saw or a hacksaw with fine teeth.

Castle marmoleum

Adhesive tiles

The tile is glued on a special glue or silicone sealant. If you use multi-colored tiles, you can lay out interesting patterns. A sketch is drawn on paper in a certain scale.

Covering tiles in a rectangular room begin to be glued from a short wall, having previously marked the laying line of the first row.

Glue is applied to the floor in zigzag lines under each tile, then it is laid and pressed firmly to the floor. For compaction, the tiles are tapped with a rubber mallet.

The next one is glued on the side. To make it fit snugly against the previous tile, use a flat wooden block. It is placed on the side and tapped on it with a hammer, pressing the tile. You can use a hook clamp, which pull the tiles to each other. So stack all the rows in sequence.

If you insert crosses for tiles between the tiles, and then seal the seams with a contrasting sealant, the floor will look elegant and beautiful.

Manufacturers

Marmoleum is an expensive material, and, like any similar coating, it is not protected from fakes. Violations of technology during manufacture greatly affect the quality, so you need to buy coatings from well-known manufacturers.

The recognized leader in the production of marmoleum is the Forbo group of companies. It was organized in 1928. The Forbo concern includes more than 40 firms located in the USA and Western Europe.

An equally large supplier to the Russian market is the British corporation Armstrong, which has its own factories in European countries.

Prices for marmoleum of various types and manufacturers

brand	Manufacturer	Dimensions	Price, rub./m 2
Marmoleum castle
Marmoleum Click, slats	Forbo, Holland	300x300x9.8	3062
Marmoleum Click, slats	Forbo, Holland	900x300x9.8	2717
Adhesive rolled marmoleum
Armstrong Marmolette	Armstrong, Germany	thickness 2; 2.5; 3.2 mm, width 2.0 m, length 21–31 m	1377
Armstrong Mokka	Armstrong, England	2; 2.5; 3.2 mm thick, 2.0 m wide, 21–31 m long	873
Marmoleum Forbo Real	Forbo, Holland	2.7 mm, width 2.0 m, length 32–34 m	919
Forbo Sports	Forbo, Holland	3.2, width 2.0m, length 32m	864
Marmoleum adhesive tiles
Dual Urban	Forbo, Holland	Thickness 2.5 mm 500x500; 333x333	1000