Air handling units Komfovent Verso. Air handling units Komfovent Verso Air handling unit verso
The VERSO series is divided into two groups: VERSO Standard, which is a standard series of installations, and VERSO Pro, which is designed for special projects. Both groups of units can be offered with rotary heat exchanger, heat pump and rotary heat exchanger, plate heat exchanger or simply air handling units.
Installation Komfovent Verso R 2500-H-E differs not only in optimal operating parameters, but also in compact dimensions: design features in VERSO Standard and VERSO Pro units allow limiting the dimensions of one of the sides of the section to 900 mm, which makes it possible not to exceed the dimensions of a standard doorway.
All standard Verso Standard units are based on the “PLUG AND GO” principle: each unit has fully integrated control automation. Verso Standard units can be shipped to the customer in a fairly short time as they are available from stock. Ventilation units have a capacity of 1000 to 8000 m³/h.
Verso Pro units have wide opportunities, the customer can select the desired installation using the software. For the convenience of customers, air heaters, air coolers and dampers are installed on outside installations - as separate sections, so the assembly of the device is greatly simplified, and the usable area is saved at the installation site of the device. VERSO ventilation units can be mounted both indoors and outdoors. The units are manufactured with fully integrated control automation. The capacity of the units ranges from 1000 m³/h to 34000 m³/h.
Benefits of Verso R units:
- Saving thermal energy
During the ventilation process, the heat from the exhaust air is transferred to the air entering the room. - Efficient heat exchanger
AT normal conditions the rotary heat exchanger does not freeze over: additional heating of the supply air is not needed even if the outside temperature drops below zero. Using a rotary heat exchanger, the energy consumption for air heating is reduced by approximately 4 times. - Air humidity balance
Under normal conditions, condensate does not form in rotary heat exchangers, since excess moisture is removed, and part of the moisture is returned back to the room. The air in the room is less dehumidified, so the humidity balance is maintained. Condensation does not fall out, drainage is not needed, all this simplifies the installation of the unit. - Low noise
The Verso R ventilation units are equipped with low-noise fans housed in a sound-insulating casing. This ensures a low overall noise level.
Benefits of a rotary heat exchanger
- High efficiency
- Does not freeze
- Four times less energy for air heating
- Regenerates moisture – reduces humidification costs
- No drainage required - installation of the unit is simplified
- Compact
- When the air conditioning is on, returns the cold from the exhaust air - reduces air conditioning costs
Temperature efficiency on demand:
Two levels of rotor efficiency are possible. Optimum efficiency is achieved with the L type rotor, higher efficiency can be obtained with the XL type rotor.
Ventilation units are manufactured with rotary heat exchangers of three types:
- Heat exchanger from aluminum foil(AL). It regenerates moisture in winter;
- Heat exchanger made of hygroscopic and aluminum foil (AZM). It regenerates moisture more efficiently than an AL type heat exchanger;
- Heat exchanger made of hygroscopic aluminum foil (AZ). This type of heat exchanger effectively controls humidity in both winter and summer.
Energy efficient EC motors
All rotary heat exchangers are equipped with EC motors, which save energy and ensure smooth rotation and control of the rotor.
Heater
For additional protection of the system, in conditions where the outdoor air temperature can be below -30 °C, it is recommended to install an air duct pre-heater.
Price: 650,000 rubles including VAT
650000 RUB
Ventilation units KOMFOVENT VERSO R represents a wide range of standard ventilation units with a rotary heat exchanger. Installation data...
Ventilation units KOMFOVENT VERSO R represents a wide range of standard ventilation units with a rotary heat exchanger. These units are equipped with high efficiency EC type fans. All equipment of the VERSO R series is equipped with a built-in C5.1 automatic control, and the client receives a ventilation unit with a fully configured and integrated automation control inside the unit, as well as an outdoor modern wall console. The air capacity of VERSO Standaet R series ventilation units is from 1000 to 7000 m³/h.
Modern digital control of installations allows the user to independently quickly and easily select and change the desired functions, control the parameters of the ventilation device directly from the control panel.
VERSO R series ventilation units with heat recovery, characterized by compact dimensions and wide choice functions, provide comfortable conditions in residential, public and industrial premises. In the production of ventilation devices of the VERSO R series, original designs, best materials and Newest technologies, so this series of equipment is economical, safe, durable and trustworthy.
Benefits of Verso R units
Saving thermal energy
During the ventilation process, the heat from the exhaust air is transferred to the air entering the room.
Efficient heat exchanger
Under normal conditions, the rotary heat exchanger does not freeze over: additional heating of the supply air is not needed even if the outside temperature drops below zero. Using a rotary heat exchanger, the energy consumption for air heating is reduced by approximately 4 times.
Air humidity balance
Under normal conditions, condensate does not form in rotary heat exchangers, since excess moisture is removed, and part of the moisture is returned back to the room. the air in the room is less dehumidified, so the humidity balance is maintained. Condensation does not fall out, drainage is not needed, all this simplifies the installation of the unit.
Low noise
The Verso R air handling units are equipped with low-noise fans housed in a sound-proof casing. This ensures a low overall noise level.
Rotary heat exchanger
Benefits of a rotary heat exchanger
- High efficiency
- Doesn't freeze.
- Four times less energy for air heating.
- Regenerates moisture - reduces the cost of moisturizing.
- Drainage is not needed - installation of the unit is simplified.
- Compact.
- When the air conditioning is on, it returns the cold from the exhaust air to the room - reduces the cost of air conditioning.
Thermal efficiency on demand: Two levels of rotor efficiency are available. Optimum efficiency is achieved with the L type rotor, higher efficiency can be obtained with the XL type rotor.
Ventilation units are manufactured with rotary heat exchangers of three types:
- The heat exchanger is made of aluminum foil (AL). It returns moisture.
- The heat exchanger is made of hygroscopic and aluminum foil (AZm). It returns moisture more efficiently than an AL type heat exchanger.
- The heat exchanger is made of hygroscopic aluminum foil (AZ). This type of heat exchanger returns moisture most efficiently.
Energy Efficient EC Drive
All rotary heat exchangers are equipped with an EC drive, which saves energy and ensures smooth rotation and control of the rotor.
For additional protection of the system, in conditions where the outdoor air temperature can be below -30oC, it is recommended to install an air duct pre-heater.
Control automation
C5 automation functions:
- 5 different modes Works: Comfort1, Comfort2, Economy1, Economy2 and Special
- Temperature control: supply air, exhaust air, indoor, balance
- The user is provided with not only the main, but also the energy parameters of the device operation: heat exchanger efficiency, heat exchanger return energy, heater energy consumption counter, fan operation time counter
- Air quality control, minimum temperature maintenance
- Flow control modes: CAV, VAV, DCV
- Weekly plant program
- Air flow display (m³/h, m³/s, l/s)
- Protection of a rotary or plate heat exchanger against malfunction
- Rotor cleaning function
- Intelligent self-diagnosis
- Night cooling in summer
- Air quality control
- Supply air temperature control
- Maintaining the minimum supply air temperature
- Combined water heater and cooler control
- Inverter type outdoor unit control
- Cooling recovery function
- Outdoor ventilation compensation
- Humidity control: air humidification and dehumidification
- Control of circulation pumps on demand
- Warm-up function circulation pumps and mixing valves
- Clogged air filters indication
- Operating mode and energy meters
- remote control via web interface
- Built-in data logger for all air handling parameters
- Application software for smartphones based on "Android" and "iOS"
Modern technologies provide a person with a lot of opportunities to create a comfortable environment not only at home, but also in places of leisure or in the workplace. However, all the efforts of designers may be in vain if the microclimate of the room is not comfortable for those in it. To avoid such annoying mistakes, you need to install air handling units.
Diversity model range HVAC equipment Komfovent Verso standard or special purpose allows you to adjust the flow fresh air in the mode you need - supplying clean air, heating it to the desired temperature, humidifying or dehumidifying. Ventilation units for industrial use they process air masses of much larger volumes, removing air polluted by industrial dust or gases from the premises and replacing it with clean air.
Each ventilation unit Verso differs in optimum parameters of work and is delivered in complete form. The dimensions of the equipment allow you to easily carry it through doorways and use it immediately after installation.
The advantages of using climate equipment of this brand are obvious:
- reducing the cost of heating a room, regardless of its area;
- long service life;
- increasing the productivity of production workers in comfortable conditions;
- increase in buyers and visitors of commercial structures.
Considering the benefits and specifications of each model, it should be noted that the housings of the R, P and CF series units are distinguished by excellent soundproofing qualities and, in combination with low-noise fans, make the operation of the unit almost silent. Series unit designs Verso R equipped with a rotary heat exchanger and have a capacity of 240 to 8000 m3/h.
In installations Verso R a plate heat exchanger was installed, which ensures efficient heat exchange due to the separation of air flows.
Models Verso RHP, except for rotary heat exchangers, are also equipped with a heat pump. This solution makes it possible to achieve high application efficiency, which is confirmed by a capacity of up to 1500 m3/h.
Series systems Verso CF with a counterflow plate heat exchanger have a capacity of up to 3500 mm3/h.
Despite the fact that Air handling units Verso S have absolutely small dimensions, this is the most efficient unit, the air capacity of which reaches 4000 m3 / h. Its design ensures easy installation and simple maintenance.
For the convenience of users, all series are equipped with modern consoles, which display detailed information about the operation of the system and it is possible to select the optimal operating mode. Also, the equipment has advanced features in the form of remote control.
Modern automation system installed on ventilation systems , increases economy and speed of each executed process. It allows you to provide for the operation of the equipment in different modes, maintain the set temperature, prevent the air heater from freezing, and much more.
At Panoramavent you can find not only the necessary brand HVAC equipment Komfovent, but also to make a purchase on attractive terms. Our experts will help you choose the appropriate size of the installations, taking into account the requirements of the customer and the parameters of the room. Buy air handling units Komfovent Verso we have - simple, profitable and reliable!
