Counters

How to remove a plastic balcony door from its hinges: step by step instructions. Ways to remove a pvc door from its hinges How to remove a closed plastic door from its hinges

Very often, during the operation of PVC products, homeowners face the question of how to remove plastic door from loops. During this procedure, it should be remembered that everything should be done carefully so as not to violate the integrity of the structure. Plastic doors can be found in any residential or public space, where they act as an entrance element. In some apartments and cottages, they serve as an integral part of the balcony block.

General characteristics of the door structure

The mechanism of plastic doors is quite simple. It includes a box and a canvas, reinforced with three or four loops. The panel is made of PVC and has a frame made of durable metal. Removal and re-installation is best done with an assistant.

Strong and durable hinges for plastic doors are complex, they are made of Teflon. It is very important to deal with them internal structure so that the structure can be easily dismantled later. The loop consists of the following elements:

door insert;
frame element with pins for fastening;
movable and adjustable sleeve located between the frame and door parts.

The loops are equidistant from each other. This helps to evenly distribute the load. The upper and lower elements are installed along the line of the box. In order to mask the fittings, plastic caps are usually put on top of the hinges. In this case, the building looks solid.

Loop mechanisms can be:

overhead (for balcony doors);
applied (for pendulum);
card: non-removable and removable;
mortise: simple and bolted;
invisible;
screw-in (for light canvases weighing up to 25 kilograms).

The choice of hinges is determined by the type of construction and profiles of the frame with sashes, the presence of an amplifier, the thickness of its walls and how the sashes will open and close.

Reasons for dismantling

The need to remove the doors may appear for the following reasons:

Breakage or displacement of fasteners.
Replacing the door leaf or individual parts.
Repair in the room.
Opening enlargement.
Moving large furniture.

It is important not only to carefully remove the canvas from the hinges, but also to subsequently install it in place.

Dismantling technology

Before removing the plastic balcony door, you first need to clarify the type of construction and pay attention to the details of the fittings. For dismantling, a simple tool is used:

screwdriver straight and Phillips;
a set of hexagons;
pliers;
wire cutters;
finisher;
mount.

The simple process of removing the door involves several steps:

All actions should not be rough and sharp, otherwise the hardware breakage is inevitable.

Before removing the doors, it is recommended to carefully cover the fittings from the plastic door with soft material or even carefully dismantle it.

Reverse installation

First, you should put the canvas in the opening so that loops can be put on top of it without any problems. You should focus on the bottom loop. The canvas must be kept straight to prevent possible distortions. Video on how to install a balcony door, see here:

Secondly, fit the end loop onto the support rod and adjust the position of other elements.

Thirdly, close the door without touching the handle and without fixing the lock.

Fourth, install the axle cylinders of each hinge in place and press on the lower pins. Its edge should go up to an audible click. The end of the rod should return to its original position and protrude from above by about fifty millimeters.

You can tighten the hinges with a hex wrench

Fifth, if necessary, twist the loops so that the canvas aligns.

Sixth, put on decorative caps and check the operation of the structure.

Before starting operation, it is useful to lubricate the hinge parts with oil or cover them with graphite shavings.

You can adjust the plastic door using a microlift and a limiter. The first fixture does a great job of troubleshooting regardless of the weight and size of the canvas. It prevents sagging of very heavy door panels. The microlift takes on part of the load, but only when it is closed. Usually it is presented in the form of a roller located at the bottom of the structure, or a movable plate at the top of the web.

The limiter helps prevent sagging of the web, and also determines the maximum angle of its opening, protecting the panel from hitting the slopes.

How to fix sagging doors?

It is recommended to open the plastic sash and find a hexagon screw on the top hinge. Using a key, the screw is rotated 2-3 turns clockwise. Next, you need to check the overall performance.

How to eliminate side rubbing of the door leaf?

On the lower canopy inside the door has a side screw. By screwing it in a clockwise direction, you can restore the position of the door leaf. It will no longer be able to rub against the side beam of the frame and will close easily.

How to establish tightness?

At the ends of the door there are special eccentrics. By rotating them, the door mode is adjusted. Eccentrics must be deployed at equal angles. In this case, the sash will close tightly. You should also adjust the canopies with special screws.

How to adjust the door handle?

Move the decorative plate 90 degrees. Under it are hidden the mechanism of the handle and the mounting screws, which should be screwed tighter. For details on debugging plastic doors, see this video:

When removing the door from the hinges, the most important thing is not to damage the fittings, otherwise you will have to go to the store or suffer with a poorly opening door.

During repairs in an apartment, office, private house, it often becomes necessary to dismantle complex structures, such as a door and a door frame. Proper execution this task will not only save the structure for reuse or repair, but also not damage the wall, which has a weak spot near the doorway. How to remove a wooden or metal-plastic balcony door will be discussed in this article.

Disassembly is a matter of minutes. However, this step must be justified. It makes sense to remove the balcony door only if:

the door is partially damaged and does not ensure the tightness of the room;
the canvas has a curvature, the double-glazed window is damaged or completely broken;
the lock does not provide a snug fit of the canvas to the box;
door curtains have exhausted their durability and should be replaced;
the room is being renovated, replacement is necessary to comply with the design.

The reasons may be different, but it is worth remembering the generally accepted rules that will help to complete this stage with minimal losses:

Replacement of a plastic balcony door is made in the winter only as a last resort.
If a complete replacement of a plastic or wooden balcony door is implied, then you should take care of a new box in advance and start installing a new canvas immediately after dismantling the old one.
For dismantling, the participation of at least two people is necessary, where the first person performs removal manipulations, and the second holds the canvas, insures the first.

Necessary tool for the job

For quick dismantling, you need to have the right tool at hand. For wooden and PVC panels, this set will be different due to the difference in the method of fastening and the material of manufacture.

Dismantling tool wooden structure frames:

Phillips screwdrivers, straight slot.
Powerful mount or large curved crowbar.
Ax with a wide blade (flat blade).
Good hammer.
Fine-toothed hacksaw (better back saw).

This basic set allows you to quickly remove the door and disassemble the box without damaging the wall. Of course, experienced craftsmen can add to the list a screwdriver, a drill with a hammer, a crowbar for dismantling platbands, but we offer a set that is sure to be found in the workshop of every man.

Plastic box removal tool:

Powerful pliers or wire cutters.
Pry bar, crowbar or solid board to create a lever.
A set of hex screwdrivers of the right size.
Powerful Phillips screwdriver.
Thin drift or blunt nail.
Sharp knife, chisel.

The set of tools differs markedly due to the characteristics of the material, different weights of the leaf, the features of dismantling standard curtains, and the complex mechanism for the balcony door.

Removing the plastic door

When all necessary tools found, it's time to study the algorithm of how to remove an unnecessary plastic door to the balcony.

The order of work is as follows:

It is necessary to fully open the mechanisms of the lower and upper hinges. To do this, the plastic plugs that close the mechanism are hooked with a knife. After that, you need to open the door a little. By inserting a drift into the upper loop, knock out the axial cylinder with a light tap. If it does not fall out freely, you need to pick it up from below with pliers, turning it and pulling it down. In this case, the punch should be pulled out of the groove. At this moment, the assistant master must hold the canvas in a strictly vertical position so that it does not lean towards the ground, does not begin to “pull out” the fasteners from the fragile frame.

After that, the door is opened at 90 °, lifted up. The lower pin cannot be pulled down - it is built into the fastener and cannot be disassembled. This operation should be done together, using a lever: scrap or board must be wrapped with a thick cloth (so as not to damage the lower edge of the canvas). The lever must rest against the lower plane and the floor. A little effort will be enough to rip the door off the bottom hinge. Having slightly tilted it towards himself, the assistant master must hold the door after it jumps off the axial cylinder of the lower hinge. Now the plastic balcony door has been dismantled. Can be repaired or replaced.

If there is a problem in the box itself under the plastic door, it is dismantled:

It’s worth starting with the dismantling of decorative platbands. This is done with a screwdriver, spatula or knife. The platband simply comes off the box itself, like a designer part.
After that, the slope panels are removed ( inner box). The process is similar to the previous point.
Then it is necessary to remove all mounting foam. A spatula or a thin-bladed knife works well for this.
The next step is to unscrew the fasteners of the box from the wall. To do this, you need a screwdriver or screwdriver.
Now you can start dismantling the frame. A mount is inserted into the gap between the box and the wall, the frame breaks out into the room.
The last step is to clean the wall from the remnants of mounting foam, fasteners.

Removing a wooden door

The process of dismantling a wooden structure is different from dismantling plastic. The sequence of execution of work differs in fewer actions, but takes much more time.

It is necessary to open the balcony door, insert the crowbar between the floor and the lower plane. Usually the canvas is removed from the curtains without much difficulty. Problems begin if the door hinges are rusted and there is no way to easily remove them from the hinges. In this case, there are two options:

Lubricate the hinges with liquid oil. By opening and closing the door, you can achieve almost complete impregnation of the curtain and then try to remove them. If this method does not help, you need to spray a solvent on the rusty curtain. Powerful chemicals in a few minutes they will corrode the rust and the door will succumb.
If the cause is a curved curtain, there is no way to remove the door from the hinges; you must remove it together with the hinges. In this case, it is necessary to break the paint that covers the fastening of the air curtain to the box, try to unscrew the screws with a screwdriver. At this time, the partner must hold the door so that it does not tear out of the box during the dismantling of the last screws. This step is justified by the fact that the damaged curtains will still have to be replaced - even if you manage to remove the door, you cannot put it back on the damaged curtains.

Dismantling a wooden box is carried out in several steps:

With the help of an ax, the outer casings are removed. The ax blade is inserted under the casing, hammered into maximum depth. Using the ax as a lever, you can quickly tear off the casing from the box.

There are two ways to remove a wooden box from the opening:

If it is possible to remove the fastening nails with which the box is nailed to the wall from the inside, then it is necessary to pull out all the fasteners, then remove the whole box. This can be done by tapping with a hammer or an ax along the perimeter of the structure. In order not to damage the tree, you can use a board that will distribute kinetic energy over a large area and prevent damage to the wood.
Otherwise, the box is cut with a hacksaw at the corners, the sides are taken out separately.

After dismantling, the walls must be cleaned of dirt, residues of fasteners.

Door installation process

This step depends on whether the box has been dismantled. If it is necessary to replace only the canvas, then the installation process repeats the dismantling algorithm in reverse order. The main thing is not to damage the new canvas with the box, because all the work is done by two masters, where the second number insures the master, firmly holds the canvas from accidental falling or damage.

Easier to change wooden door- it is simply put on the hinges and then adjusted to the frame using rubber gaskets (provided that the dimensions of the opening are taken into account when assembling a new canvas.

Plastic involves a more complex process, where it is important to raise the pins in time and achieve maximum fastener strength.

Harder to set up the box. Installation must begin with the processing of the walls: drilling new holes for fasteners (it is not recommended to use the old ones). PVC and a wooden box are inserted in a similar way: in the already assembled state, it is mounted in the opening, tacked by the installation. For a wooden frame, it is better to use powerful self-tapping screws with a dowel (quick installation). Less commonly, special nails for concrete or liquid adhesives are used. PVC panels are mounted on a mounting frame - thin metal plates.

Let's imagine a situation: your new acquisition, your pride - a plastic door - has stopped closing. After the installation, carried out by the company's employees, there were some doubts about the correctness of the installation. The design was closed with some distortion, the lock was broken or closed only if force was applied. What to do? Again to call the same "workers"? No, you need to do it once and conscientiously.

How to remove the door?

During the repair process, you may need to remove the canvas from the hinges, but how to do this? Let's tell now! Let's start with a little theory.

General device

The material used for the manufacture of doors is polyvinyl chloride. Plastic is an indispensable material in terms of water resistance. Moisture threatens both external and internal doors. With external doors, it is clear that this is direct contact with the humidity of the atmospheric air, and condensate from internal evaporation.

Interior doors face particularly damp conditions in kitchens and bathrooms. Of course, plastic is only a coating; steel plates are attached inside the structure. In addition to the canvas itself, the kit includes a non-separable door frame. (photo) In order for the door to fulfill the functional requirements, it is necessary to have a special type of parts in the door structure called fittings.

Entrance plastic structures are quite heavy, because they have a multi-chamber structure and burglary protection. In connection with this and with other features of this type of device, special loops are used to connect the web to the box. This is the main part of the fittings, the main part of the design of the plastic door. Loops are divided into:

removable;
fixed;
screw;
card;
invisible.

The very name screw hinges, along with overhead and applied ones, speaks of the method of attaching the hinges to the door.

Hinges for plastic doors are made of highly durable materials based on Teflon. In addition to the fact that the hinges carry the load from the door leaf, they must ensure easy walking of the door and a snug fit of the leaf to the frame.

Information on how to properly remove a plastic balcony door from its hinges will be very useful for every homeowner. Such a need can arise in every home at any time. In order not to spoil the design, it is important to know some rules for performing this work.

Plastic door hinges differ significantly from conventional door fittings.

Plastic doors are installed today almost everywhere. In apartments and private houses, they are part of the balcony block, and in public places and offices they serve as the front door.

The design of the plastic doors themselves is not much different from the usual ones. Here, too, the main parts are the box and the canvas attached to the hinges. Their number is usually 3-4 pieces, which allows you to evenly distribute the load. The material itself combines polyvinyl chloride and a metal frame.

Door blocks are most often supplemented with a glass insert, so use extreme caution when working. It is best to carry out the dismantling and reassembly with an assistant who will support the door and insure you.

Loops are located at an equal distance from each other. The upper and lower elements are attached along the line of the box. In order for the fittings not to attract attention, camouflage plastic caps are put on top of the hinges. So the design looks holistic and neat. All fasteners are hidden under these linings.

Plastic doors are very popular and are used almost everywhere.

When may it be necessary to dismantle the door leaf in the balcony PVC block? Basically, this situation is related to repair work indoors or the structure itself. For example, knowledge on how to remove a plastic door may be needed in the following cases:

Breaking. If any part of the fasteners fails or is displaced, the door needs to be adjusted. Sometimes you need to take it off the hinges to do this.
Replacing a door or part. You may have to face the problem when you need to make a complete replacement of the hinges or the canvas as a whole.
Repair work in the room. In order not to stain or damage the structure, you can cover the door with cellophane, but sometimes best solution is a temporary dismantling.
Opening expansion. This refers to the situation of simply removing the door, for example, when moving furniture.

In any case, you need to not only carefully remove the canvas from the hinges, but then be able to put it in place or install a new design.

Most often, the removal of a plastic door is required during repair work.

Consider how to properly remove a plastic door from its hinges. The whole process can be divided into several stages:

Removing pads. First you need to open the hinges, that is, remove the protective caps from them. To do this, you need to cover the door, but do not lower the handle down, and then pry off the trim with a screwdriver and bend the plastic.
Loop disassembly. In order for the mechanism to loosen, it is necessary to press the loop in its upper part so that the protruding pin drops down. This way it will come out from below. To completely remove the axle, pick it up with pliers.
Removing the canvas. Grasp the canvas well and tilt it slightly towards you. Then lift the door up. The loops must come apart. Be careful, as the weight of the structure is rather big.

Removing the plastic door from the hinges

When all the necessary operations have been completed and there is no longer any need for an empty opening, it is important to correctly install the door in place. To do this, in fact, you need to perform all the above manipulations, but in reverse order:

Insert the canvas into the opening so that you can put it on top of the hinges. The bottom hinge serves as a guide, but it is important to maintain a level position to prevent distortions.
Put the lower loop on the support pin and correct the position of the remaining elements.
Move the door to the closed position without fixing the lock. If you turn the handle, the canvas will move and you will not be able to put on the rest of the hinges on the axis.
Install the axle cylinders of all hinges in place and press the pins from the bottom so that its edge goes up until it clicks. The edge of the pin should return to its original position and protrude from above by about half a centimeter.
Tighten the hinges if necessary to align the door diagonally.
Put the decorative caps back on and check how the design works.

It is far from always necessary to remove the door leaf in the event of a malfunction in the structure. Modern plastic doors in the balcony block can be easily repaired on site. To do this, you need to turn to tools such as a screwdriver and a hex wrench.

First you need to remove the protective caps from the hinges. Pry them off with a screwdriver and pry them out. They can be the cause of the poor functioning of the door. In order to fix this problem, sometimes it is enough to lubricate them. If a skew is detected, the position of the blade must be adjusted. To do this, in the loops with a screwdriver or a hex wrench, you need to set the necessary adjustments. They have special holes hidden under the caps. With the help of such simple manipulations, you can repair the structure with little effort.

In order to avoid problems with the door again in the future, you should lubricate its parts and correctly adjust the position of the leaf. Periodically check the condition of the structure and fix problems as they are identified.

Metal-plastic are now gaining more and more popularity, so it would be useful to learn the basic rules for servicing its individual elements. In this article, we will consider how to remove the plastic door from the hinges on the balcony in case of repair or replacement.

Fastens to the opening with metal loops. There are usually two or three of them to evenly distribute the load. They are equidistant from each other, and are closed from the outside with special plastic caps. Each hinge, in turn, consists of two metal elements: fastening the frame of the double-glazed window and directly to the door frame.

The redistribution of weight and load is carried out by a remote sleeve. If necessary, it is best to dismantle the balcony door leaf with the help of an assistant, because the design is quite heavy. Careful actions without unnecessary jerks and efforts will ensure the desired result and the integrity of the structure.

Why you may need to dismantle:

Repair of individual elements of the door structure.
Moving large furniture.
Temporary measures in case of repair in the main or balcony room.
Door leaf replacement.
Expansion of the doorway.
Annual lubrication procedure door hinges will also require the removal of the canvas.

Door fittings, despite serious loads, can easily be damaged during careless operation. That is why, if it is necessary to remove, you should be extremely careful and first study the instructions below.

How to remove a balcony plastic door

The dismantling process consists of several stages. In the design of plastic doors, the most vulnerable point is the glass panel, which is why additional help is needed to hold the canvas and prevent damage.

Before work, it is necessary to prepare tools: a screwdriver, a set of hexagons, pliers and any lever in order to lift the door from its hinges (mount, crowbar, wooden beam).

Work sequence:

Reverse installation

Instructions on how to remove door leaf, would be incomplete without the reverse sequence - installation. To do this, you will need about the same set of tools and an assistant with whom the process will be easier and less traumatic.

How the doors are installed:

The door leaf is installed opposite the hinges. Initially, it is necessary to align the position of the lower hinge, from which the installation will begin.
Bring the hole in the lower loop onto the support rod, in parallel adjusting the location of the web relative to the rest of the loops.
Close the door leaf without pressing the handle.
Start alternately the axis of the middle and upper mechanism. The correctness of the action is determined by the click that the pin makes when it hits the desired position.
Using a hexagon, fasten the hinge fasteners.
Check the opening/closing process.
Install decorative and protective plastic lining.

The balcony door is not very heavy, but during its installation it is important to avoid any distortions. That is why it is better to mount the structure together.

How to care for loops

After dismantling the balcony door, it is better to revise the hinges, as well as lubricate the mechanism. This will help extend the useful life and prevent jamming.

What needs to be done for this:

Clean hinges and all connecting elements from possible dust and dirt. It is better to do this with a piece of rag soaked in gasoline.
After treatment, thoroughly wipe the contaminated areas dry.
Lubricate the rubbing structural elements with special mineral oil. If use lubricants in the packing of an oiler, periodic maintenance can be carried out without removing the door from its hinges.

Important: The use of unsuitable substances for lubricating door hinges is not permitted. There should be no solid particles in the lubricant, this can lead to failure of the entire mechanism. It is better to purchase a special oil, which can also be used for periodic maintenance plastic windows.