Silicone nozzle sizes. Silicone tube Ø64 mm (RED)
A branch pipe is a small part of a pipe attached to a tank or other structures. With the help of these products, they are connected to fittings or a pipeline that drains liquid, steam or gas. Branch pipes connect the nodes of the engine compartments, cooling, heating systems, as well as other equipment. They perform connecting and shock-absorbing functions.
One of the activities of Penta Junior is the production of silicone pipes of various sizes. Products are made from high quality silicone reinforced with several layers of polyester fiber.
Benefits of silicone tubes
- Preservation of the geometry of the product with repeated temperature changes.
- Elasticity, providing a tight and uniform fit of parts to clamps and connecting surfaces. Over time, the material does not harden, it does not crack, the tightness of the product and the connection is maintained, the working fluid does not leak, and air does not enter the system.
- Durability - Silicone parts last longer than similar rubber products, which harden and break after a few years. This reduces operating costs.
- Strength, high wear resistance, due to the peculiarities of the production process, in which the penetration of silicone into the reinforcing fabric occurs.
- Resistant to solar radiation, aggressive chemical substances, coolants, antifreeze, ozone and other gases, oil vapors.
- Easy to install and replace.
Features of silicone nozzles
- Preservation of operational qualities in the widest temperature range, from -60 to +250 °С.
- Vacuum resistant and high pressure, and at excess pressure, the expansion of the nozzle itself is minimal.
- A variety of sizes, bending angles, wall thicknesses and transitions to different diameters makes it possible to lay air lines of complex configuration.
Types of pipes:
- straight;
- corner;
- transitional;
- damper.
When choosing silicone nozzles, one should take into account the operating parameters, first of all, pressure, take into account the shape of the products and the quality of the clamps.
Silicone nozzle: size chart
| Inner diameter, silicone tubes mm | Outer diameter, silicone tubes mm | Length of silicone pipes, mm |
| 40 | 55 | 450 |
| 40 | 46 | 600 |
| 40 | 44 | 600 |
| 50 | 60 | 800 |
| 56 | 76 | 400 |
| 60 | 66 | 900 |
| 61 | 69 | 950 |
| 64 | 74 | 1000 |
| 67 | 75 | 1000 |
| 68 | 77 | 600 |
| 75 | 100 | 210 |
| 77 | 87 | 400 |
| 85 | 110 | 250 |
| 88 | 112 | 300 |
| 92 | 98 | 400 |
| 100 | 110 | 800 |
| 100 | 110 | 850 |
| 104 | 112 | 300 |
| 110 | 115 | 750 |
| 114 | 120 | 300 |
| 129 | 134 | 750 |
| 150 | 157 | 300 |
| 160 | 170 | 500 |
| 160 | 166 | 500 |
| 204 | 210 | 1000 |
| 304 | 314 | 200 |
You can also order the production of silicone nozzles according to individual sizes.
Silicone pipe: purpose
These products are indispensable in the automotive industry, in the production of ventilation and cleaning systems, as well as in other areas.
The Rezinoplast enterprise produces various rubber fittings of the cooling system (pipes, sleeves, hoses, cuffs, seals, rings, gaskets) that meet international standards, as well as according to customer drawings or samples. The enterprise has extensive experience in designing and manufacturing molds for the production of rubber goods.
Rubber pipes for cooling systems - short pipes that serve as a drain from the main tank or pipeline, and also act as a connecting part in the cooling systems of engines of agricultural machinery, special equipment, trucks and cars. Depending on the connection and the type adopted, the cooling system pipe at the end is equipped with a thread, socket or flange.
In 2013, an extrusion line, made in Korea, was purchased and put into operation, industrial hoses reinforced with textile thread were put into production, withstanding pressure up to 20 bar, automobile and for tractors branch pipes of the cooling system, profiles of various designs.
Extrusion line for the production of pipes, sleeves, hoses and profiles.
In close cooperation with the production, the design department of the Rezinoplast company works, whose specialists in the shortest possible time can create a project of a forming tool that fully meets the tasks and standards, and develop a technology for the production of the desired product.
The production capacity of the enterprise allows to produce up to 7 km. oxygen hose diameter 9mm. per day. Produced reinforcement of two types: strapping and braiding, allow the production of rubber reinforced pipes, distinguished by the highest quality, wear resistance and durability.
The line allows the production of gas welding, watering, pressure hoses, rubber pipes, diameter from 6 to 80 mm and is equipped with a system for automatically measuring the inner and outer diameters of the sleeve, which makes it possible to control its dimensions and geometry at the production stage. Rezinoplast manufactures a range of pipes designed primarily for use in automobiles and agricultural machinery for supplying coolant.
Rezinoplast manufactures a range of pipes designed primarily for use in automobiles and agricultural machinery for supplying coolant. The multilayer structure of which has a higher oil, thermal and wear resistance. The products are resistant to glycol and non-aggressive chemicals. Withstands temporary temperatures up to +120°C. Products in the autoclave are processed with steam at a temperature of 160 degrees and a pressure of 6 atmospheres.
Our company produces profiles of round, rectangular and complex sections.
Tall professional level specialists of the enterprise, the use of high-quality raw materials allows us to produce a product that can compete with European manufacturers.
Quality control of RTI is carried out by the product quality department at all stages: when purchasing raw materials, preparing rubber compounds, after manufacturing products. The quality is checked by the company's laboratory equipped with specialized equipment.
Rezinoplast manufactures pipes for the cooling system for the Minsk Tractor Plant, Bogdan Corporation and AvtoKrAZ.
The company produces branch pipes for engine radiator cooling systems and heating systems for : KAMAZ, MAZ, ZIL, KRAZ, GAZELLE, GAZ, PAZ, UAZ, URAL, VAZ-2101/02/03/04/05/06/07/08/2110, LADA, TAVRIA-ZAZ, MOSKVICH, NIVA, MERCEDES , DAEWOO, VOLVO, MAN, VOLKSVAGEN. For tractors: URSUS, VALMET, T-150, YuMZ, MTZ, K-700, DON, BTR, NIVA, JOHN DEERE, KLAAS, DEUTZ, CASE, NEW HOLLAND combines, JCB, CAT, KOMATSU excavators, HYSTER, MANITOU loaders, BALKANKAR, universal angular transitional pipes for cars and agricultural machinery of world manufacturers and according to the individual order of the client. Rezinoplast manufactures branch pipes of any diameter and any complexity, for all types of machinery and equipment.Universal spigot made of multi-layer high-quality reinforced silicone, ensures high performance even under the most severe thermal overloads. Withstands high pressure, is not afraid of an aggressive environment. It has a long service life unlike rubber pipes. It can be applied anywhere in the car's cooling system.
Despite the presence of 3-layer reinforcement, it is permissible to stretch the branch pipe up to 4 mm in diameter when installing it on a non-standard part size. If the part does not have a suitable size of the nozzle, then you should choose a similar size of the silicone nozzle to the smaller side.
On a note:
Most cars, regardless of the country of manufacture and the manufacturer itself, are produced from factories with rubber pipes and hoses. The suitability of rubber products used by many manufacturers leaves much to be desired. This is due to the fact that rubber, even in excellent working conditions, quickly becomes obsolete and wears out, as a result of which it breaks and hardens. You should worry in advance about the impending disaster and warn yourself against all the negative impacts of this aspect. All rubber products will not tolerate changes in temperature. That is why they should be changed very often if the car is operated in cold seasons. If the motorist wants to protect himself at all, he should purchase exactly silicone pipes, with which life will become much easier. Such devices have a fairly low wear, as a result of which they are long-lived and can serve for more than one year. That is why many motorists have opted for silicone type pipes, which have many different advantages over their world counterparts, which are gradually leaving the automotive market.
What are silicone tubes?
Silicone hoses and pipes are a very important attribute when assembling all turbocharged engines as in domestic vehicles, and on foreign cars. It is important to note that this kind of silicones have many advantages, as a result of which they have achieved wide popularity among domestic consumers.
Firstly, such devices have a reinforced structure, which will allow them to withstand very strong pressure, and the expansion of the nozzle itself with such excess pressure will be minimized. It is in this way that it will be possible to smooth out the “turbo-lag” or “turbo-lag” even more, as a result of which the time before the onset of boost will be reduced. In addition, the use of such pipes will make it very easy to make a connection different pipes and parts of parts among themselves. It is silicone pipes that will play the role of irreplaceable elements, as they are the most versatile and durable parts of their kind, through which maximum and effective work the entire cooling system of the vehicle.
The role of silicone tubes.
It is important to note that silicone pipes will play the role of the main connecting elements of the car's cooling system. They will also serve as channels for the distribution of coolant. Their location will not matter at all - between the radiator and the pump, between the engine and the thermostat, since they necessarily have an increased level of wear resistance. In addition, they are not afraid of a terrible aggressive environment and different kind substances.
It should be noted that you only need to purchase silicone pipes that are very similar to your previous factory parts, so the most normal operation of the entire cooling system will be guaranteed.
Universal spigot made of multi-layer high-quality reinforced silicone, ensures high performance even under the most severe thermal overloads. Withstands high pressure, is not afraid of an aggressive environment. It has a long service life unlike rubber pipes. It can be applied anywhere in the car's cooling system.
Despite the presence of 3-layer reinforcement, it is permissible to stretch the branch pipe up to 4 mm in diameter when installing it on a non-standard part size. If the part does not have a suitable size of the nozzle, then you should choose a similar size of the silicone nozzle to the smaller side.
On a note:
Most cars, regardless of the country of manufacture and the manufacturer itself, are produced from factories with rubber pipes and hoses. The suitability of rubber products used by many manufacturers leaves much to be desired. This is due to the fact that rubber, even in excellent working conditions, quickly becomes obsolete and wears out, as a result of which it breaks and hardens. You should worry in advance about the impending disaster and warn yourself against all the negative impacts of this aspect. All rubber products will not tolerate changes in temperature. That is why they should be changed very often if the car is operated in cold seasons. If the motorist wants to protect himself at all, he should purchase exactly silicone pipes, with which life will become much easier. Such devices have a fairly low wear, as a result of which they are long-lived and can serve for more than one year. That is why many motorists have opted for silicone type pipes, which have many different advantages over their world counterparts, which are gradually leaving the automotive market.
What are silicone tubes?
Silicone hoses and pipes are a very important attribute when assembling all turbocharged engines, both on domestic vehicles and on foreign cars. It is important to note that this kind of silicones have many advantages, as a result of which they have achieved wide popularity among domestic consumers.
Firstly, such devices have a reinforced structure, which will allow them to withstand very strong pressure, and the expansion of the nozzle itself with such excess pressure will be minimized. It is in this way that it will be possible to smooth out the “turbo-lag” or “turbo-lag” even more, as a result of which the time before the onset of boost will be reduced. In addition, the use of such pipes will make it very easy to connect different pipes and parts of parts to each other. It is silicone pipes that will play the role of irreplaceable elements, as they are the most versatile and durable parts of their kind, through which maximum and efficient operation of the entire car cooling system will be ensured.
The role of silicone tubes.
It is important to note that silicone pipes will play the role of the main connecting elements of the car's cooling system. They will also serve as channels for the distribution of coolant. Their location will not matter at all - between the radiator and the pump, between the engine and the thermostat, since they necessarily have an increased level of wear resistance. In addition, they are not afraid of a terrible aggressive environment and various kinds of substances.
It should be noted that you only need to purchase silicone pipes that are very similar to your previous factory parts, so the most normal operation of the entire cooling system will be guaranteed.
Suitable clamp:
Power clamp 67-75 mm (T-bolt, stainless steel)
Suitable aluminum pipes:
