Pipes

How to attach a crane to a barrel. How to embed a crane into a barrel - features of the operation

Everyone who has ever used barrels or huge canisters knows how uncomfortable it is to drain liquid from them, especially if they are filled to the top. In order to simplify this task, it is possible to improve the container, in particular, to insert a drain tap into it. Below we will consider in detail how to insert a tap into a barrel so that the container does not lose its tightness along with this.

General Information

The drain valve is a very ergonomic device, because thanks to it the container does not need to be turned over or lifted. In addition, the drain is carried out carefully, without splashing the liquid, which is also very important in some cases.

Inserting a tap into a barrel is a relatively simple procedure that every home master can do. The only thing to point out is that this process is highly dependent on the material from which the container is made.

Based on this, below we will look at how to embed a tap into a metal barrel and a plastic container.

Drain insert

In an iron barrel

Place the drain to be guided as low as possible. But, this should not be done at the bottom, since such an insert will significantly reduce the functionality of the structure and require the execution of a special pedestal for it.

The following materials are useful for embedding:

The price of all these materials is not high, so the cost of this operation is minimal.

Note! Before proceeding with the drain insert, go to clean the inner surface of the container from dirt and rust.

So, the instruction for the execution of this work is as follows:

Before plunging the crane into iron barrel, it is necessary to outline the location of the drain. To do this, you can use a simple compass.
After that, a hole must be drilled in the indicated place.. If necessary, the hole can be enlarged with a round file. The main thing is that it matches the diameter of the drive.
Then, from the side of the small thread of the drive, go to screw the lock nut, after which it is inserted from the outside into the prepared hole.
Then from the inside you need to make a second lock nut.
Wrap a fum tape on the free part of the thread and generously apply silicone sealant for pipes.
Then you need to carefully tighten the connection. This must be done with the application of effort so that the deformation of the wall occurs at the place of compression.
Now it remains only to fasten the shut-off valves to the drive and check the system's performance..

This completes the do-it-yourself drain tie-in process.

In a plastic barrel

Now let's look at how to embed a crane in plastic barrel. it is best to perform this procedure with a heat gun and hot glue.

If there is no similar tool, then tapping into a plastic barrel can also be done using a threaded connection. The only thing, in this case, you need to take care of sealing the joint.

This is done as follows:

As in the previous case, before inserting a crane into a plastic barrel, it is necessary to outline and drill a hole. If the plastic is soft, the hole can be cut with scissors or sharp knife.
After that, you need to prepare a mortise crane for a plastic barrel. To do this, from the side of the thread it is necessary to install a huge iron washer and a waterproofing rubber gasket.

Then sealant must be applied to the gasket and washer, as shown in the photo.
Then the inlet pipe of the device must be inserted into the hole and otherwise, in addition, put a rubber gasket and washer on the thread, treating the joint with a sealant.
At the end of the work from the inside, it is necessary to screw the nut onto the thread.

Typically, the container has a narrow neck, as a result of which it is unrealistic to screw the nut on from the inside. Under such conditions, a fitting that owns a flange on one side is useful.

Work under these conditions is performed in the following order:

First of all, it is necessary to make a hole in the container according to the diameter of the fitting.
After that, the fitting must be fixed on an iron wire, which will allow it to be pushed into the hole from the inside of the canister through the neck and then pull out the wire. To do this, it is possible to tie a limiter to the wire on one side.

Before inserting the fitting into the hole, the place where the flange fits to the container wall must be lubricated with a sealant, in addition, a rubber gasket can be used.
Then the wire is pushed through the neck into the hole and so the fitting is pulled out. Holding it with a wire, screw the locknut onto the thread from the outside, after installing the rubber gasket and treating the joint with sealant.
At the end of the work on the fitting, you need to screw the shut-off valves.

Advice! In order to make the canister more ergonomic, it is possible to embed a second neck into it, on the opposite side of the first. Under such conditions, the water will drain evenly.

This completes the embedding process.

Conclusion

Inserting a tap into a container does not require huge financial and effort costs, but at the same time makes it much more ergonomic to use. The only thing is to do this operation carefully, adhering to the above recommendations, so as not to break the product.

From the video in this article, it is possible to draw some additional data on the designated topic.

Having a tank at their disposal, many resort to buying a tap for a plastic barrel. The motives for this may vary, but inevitably the owner is faced with the problem of integrating a drain device into the structure. On the one hand, this is quite simple - the material of the case makes it easy to make a hole in it. But in practice, one always has to face difficulties, and one cannot do without instructions.

A tap for a plastic barrel - a practical solution

This solution makes it possible to simplify the draining of the liquid from the tank, making it quick and convenient. Many have tanks that hold more than 100 liters, and then the problem of using it arises - it is inconvenient and difficult to tilt, it is almost impossible to get liquid from the bottom. A barrel for water with a tap makes it possible at any time to get as much liquid as you like, dose it, and regulate the pressure.

Before you insert a tap into a barrel, you must select it. But it is worthwhile to immediately estimate how it will be attached. We will consider a drain option that is equipped with an internal thread.

Those who use plastic cans know how inconvenient it is to use them and pour something out of them, especially when they are full. The canister will definitely “gurgle” and splash out some of the contents past. And it’s good if it’s just water, and not gasoline, oil or a combustible mixture for a two-stroke lawn mower or chainsaw engine. You have to completely lift the canister in your hands and so that its neck is at the very top, and carefully drain the contents. But the canister can be quite heavy and contain dangerous liquids. In addition, funnels of large diameter are constantly required so that this content does not splash out during the “gurgle”.

To avoid such troubles, it is necessary to equip the canister with another “neck” - a small-diameter fitting with a stopper, or a small faucet. Through them you will spend the contents of the canister.

From the tools we need a heat gun and hot glue. With their help in plastic canister perfectly and reliably you can glue any fitting or tap. To do this, it is enough to make a hole in a place convenient for further use of the canister and glue the fitting.

But such a technique is good to use when the fitting flange is not flush with its end, but, as it were, in the middle of the fitting. Then part of the fitting enters the canister and is perfectly fixed. And secondly, the contents of the canister are not under pressure. Otherwise, it will constantly strive to pull the fitting out of the canister wall. And adhesives don't work very well for tearing.

Therefore, it is always good if the fitting flange is located inside the canister. Then the liquid pressure would always press the flange of the fitting or tap against the canister wall and not tear it off. But how to do it if the neck of the canister is narrow, and the hand does not go there?

The task is actually solved quite simply, with the help of a strong rope or wire. We pass it through the neck of the canister and release it through the fitting hole. This rope or wire will serve as both a conductor for the fitting and its clamp when gluing.

We put a fitting on a rope or wire, and tie a “cork” to the rope, such that it goes into the neck of the canister, but does not go into the fitting itself. Behind the cork, it is desirable to leave a “tail” at the rope, for which we will then pull the cork back. Now our fitting, as if by a thread (it is actually on a thread) will fall into desired hole. If you pull the rope or wire, the cork will press the fitting against the wall and we can apply glue without any problems. Rather, it must be applied immediately before pressing the fitting.

Of course, you can also use the threaded method of attaching the fitting to the wall of the canister. It is only necessary to use reliable elastic gaskets to seal the junction of the fitting and the canister wall.

Thus, you can equip the canister with another neck and use it will become much more convenient. So that the canister does not “gurgle”, before using a new neck, it is necessary to slightly unscrew the plug on the main neck so that air freely penetrates into the canister as the liquid flows out of it.

The photo shows an example of how a “faucet” from a bag of wine is embedded in a canister. Supermarkets sell wine in 3-5 liter boxes. In fact, inside the cardboard bag is a plastic bag equipped with a faucet that operates on the principle of "pressed - flows". The package itself is quite problematic to use. But here's a faucet from him - it can serve. With the help of such a canister, it is extremely convenient to fill a chainsaw or lawn mower with a fuel mixture. Funnels are not required. The spout of the faucet is quite narrow, it is brought to the filler neck of the gas tank and a trickle of the fuel mixture flows exactly into the tank. “Not a drop of fuel to the enemy” (and to the ground). It is possible to fill in fuel literally for a minute of work. This is usually important when running 2-stroke engines, as it is not recommended to leave fuel in their tank and especially the carburetor. Gasoline evaporates, oil remains, and as a result - a serious complication of the next start. Therefore, it is better to refuel the best 2-3 times during operation than to fill in fuel “under the cap” and then drain it or run it empty.

It is also convenient to embed (paste) the second neck into the canister at the top, but from the opposite side, relative to the main neck. This second neck makes the use of the canister much more convenient.

Sometimes at the disposal of the summer resident are metal barrels with a narrow hole in one of the dons, closed with a screw cap. Using such barrels directly is very difficult and inconvenient. The neck in such a barrel is so narrow that even a child's hand will not fit into it. And the summer resident, gritting his heart, decides and cuts off the lid of the metal barrel entirely. But rainfall, garbage, dust fly into an open barrel ... Water in a barrel gets dirty much faster. Or generally refuses to use such a barrel.

The method described above makes it easy to embed the fitting anywhere in the barrel. Even at the bottom, at least in side surface. Of course, either welding or epoxy resin, or simply, a threaded connection with gaskets. Thus, the summer resident can use "uncomfortable" barrels for their intended purpose. It is especially good to use such a barrel as an intermediate receiver for a small pressure, 0.3 - 0.5 atm, since open barrels cannot be used in this way. Or as a container summer shower. Neither dirt nor debris will get into such a barrel. Yes, and it is easier to insulate such a barrel. You can also use the barrel in the “lying” position, and not just vertically. Sometimes it's the most best way its placement, for example, as a storage tank for water in the attic.

Many summer residents and motorists have repeatedly encountered the use of large canisters or barrels. Therefore, they probably know how inconvenient it is to handle, drain or pour liquid, especially if they are filled to the brim. Installing a drain valve will help solve this problem. In this article, we will provide useful advice, regarding how to embed a tap into a metal barrel or plastic canister.

Why should you use a faucet?

Drain valve - incredible handy device, because thanks to him you can easily drain the liquid, while you do not need to lift or turn the container. The process itself is carried out carefully, the liquid does not splatter, which in most cases is very important.

It is impossible to call the procedure for tapping a tap into a barrel simple, but anyone can handle it. House master. But by all means it is worth noting that the material from which the container is made is of great importance here. That is why below we will give examples of how to embed a drain valve into a plastic and iron barrel. Try to follow the recommendations described, since its performance and service life largely depend on this.

How to embed a tap into a metal barrel yourself?

Before you embed the crane into a metal barrel, mark its location, it is better to place it as low as possible. The main thing is not to overdo it, not to do it on the bottom, since such a tie-in option greatly reduces the functional properties of the structure and requires the installation of a special pedestal.

Prepare the following materials for work:

Sgon is a threaded pipe.
Tap. For such purposes, as a rule, ball valves are used. It is important that its branch pipe has an internal pipe thread so that it is convenient to wind the tap onto the squeegee.
Lock nuts. They will come in handy for fixing the drive.
Sealant and FUM tape. They are necessary for sealing joints.

Important! All these materials are inexpensive, so this operation will not hit your family budget. Before starting the tie-in, be sure to clean the inner surface of the barrel from rust and dirt.

Perform a tie-in crane according to this scheme:

Don't forget to mark the location of the drain. Use for this the most ordinary compass.
Then drill a hole at the indicated point.

Important! If necessary, you can expand it a little with a round file so that it matches the diameter of the drive.

Screw on the locknut from the side of the short thread of the spur. Insert it into the prepared hole from the outside.
Screw in the second locknut from the inside.
Wrap the FUM tape on the free part of the thread, lubricate this place with a thick layer silicone sealant for pipes.
Tighten the connection carefully. Apply as much effort as possible so that the walls are slightly deformed at the place of compression.
Screw the shut-off valves to the shackle, check the operation of the system.

How to equip a plastic barrel with a crane with your own hands?

Now it's time to consider how to embed a faucet into a plastic barrel.

Important! This procedure is recommended to be carried out using a special gun and thermoplastic glue. If you do not have such tools at hand, then you can tie in using a threaded connection. Only then will you have to take care of the proper sealing of the joint.

You need to do the following:

As in the previous case, mark and drill a hole on the plastic barrel for tapping.

Important! You can use a sharp knife or scissors if the plastic is soft enough.

Prepare the faucet. From the side of the thread, install a large metal washer and a rubber gasket for waterproofing.
Apply a thick layer of sealant to the washer and gasket.
Insert the inlet pipe into the hole, put a washer and a rubber gasket on the thread on the other side. Seal all joints with sealant.
Screw the nut onto the thread from the inside.

As a rule, such containers have a narrow neck, so there are problems with tightening the nut from the inside. If you come across just such a barrel, then use a fitting equipped with a flange on one side. Do all the steps in the following order:

Make a hole in the container according to the diameter of the fitting.
Fasten the fitting to a metal wire so that it is more convenient to push it into the prepared hole from the inside of the canister directly through the neck, then pull out the wire.

Important! Do not forget to tie a limiter to the wire on one side.

Before placing the fitting in the hole, lubricate the place where the flange fits to the barrel wall with sealant.
Insert the wire through the neck into the hole, pull the fitting out. At the same time, try to hold it with a wire. Then, screw the locknut onto the thread from the outside, after putting a rubber gasket on it and treating the joint with a sealant.
Screw the shut-off valve onto the fitting.

Important! To make your canister more convenient, cut an additional neck into it from the opposite side. This will allow the water to drain evenly.

In this article, we will talk about how to make a faucet in a plastic barrel using the simplest valves that can be purchased at any plumbing store. But before embarking on this simple task, let's decide what is the need to equip the tank with drain mechanisms.

At present, it is not problematic to purchase a plastic container of 200 or more liters. These useful containers can be used for accumulating and storing water intended for watering a summer cottage for arranging a summer shower, etc.

However, there is a problem, plastic containers, most often, are not equipped with a drain mechanism. At the same time, the price of a barrel with a faucet already installed is high, and therefore it's time to learn how to make an adjustable drain with your own hands.

So, how to put a tap on a plastic barrel and what is needed for this?

We select the necessary fittings and consumables

Before attaching a crane to a plastic barrel, let's decide what is needed for this.

In addition to the barrel itself, you will need a special fitting, tight gaskets to seal the connection and shutoff valves that fit the design of the fitting.

A mortise fitting with a seal is a type of fitting designed to hermetically connect a pipe or flexible hose to plastic or metal containers.

Fittings of this type, presented on the market, are divided into polymer and metal products according to the type of production materials.

Metal fittings for tapping are made of stainless steel or brass. Such fittings are good in corrosion resistance, strength and durability.

Important: When purchasing mortise fittings, avoid buying low-quality cheap products, as such fittings are often made from silumin.
As a result, literally after a couple of months of operation, such a tie-in will become unusable, since the material used in the production will crumble.

Polymer fittings for a sealed device, most often they are made of polyethylene.

The advantage of polyethylene products is their elasticity. As a result, even if the nut is overtightened, it will not crack properly and will provide the required tightness.

Important: Polymer tapping devices are not designed for installation in containers with a volume of more than 100 liters, as they can withstand a pressure of not more than 4 atmospheres.

Choosing best option from the range of products on the market, we pay attention to the end fitting of the mortise fitting. For the installation of a full-fledged shut-off valve, we need a product with a threaded end. If a plastic barrel is used to collect water used for irrigation, you can use a fitting with a trailer designed to fix a flexible hose.

Now we know what needs to be purchased for the tie-in, but before inserting the tap into the plastic barrel, we need to select the appropriate shut-off valves.

The valve must match the diameter of the end fitting. In addition, it is desirable that these devices are made of the same materials. That is, it is desirable to install shut-off valves made of similar materials on a brass tie-in. The same is true for stainless steel products.

For the operation of plastic drums in living conditions There are two types of cranes:

traditional modifications with one rotary valve - a universal, easy-to-install solution, the price of which is low;
ball valve "American" - optimal solution for arranging a summer shower and similar structures, where the shut-off valves are stationary.

Features of the installation work

So, now a few words about how to install a faucet in a plastic barrel.

Instructions for conducting installation work simple:

At the bottom of the plastic container, we make a mark at the place of the upcoming tie-in.
We insert a drill into the electric drill, the diameter of which is 1-1.5 mm larger than the diameter of the fitting seat.
We drill a hole and clean its edges from burrs and bumps.

Next, remove the union locking nut from the fitting and leave one sealing ring.
We push the prepared fitting into the hole from the inside of the barrel.
Next on outer part fitting, we put on the sealing ring and bait the fixing nut.
Now holding the mortise device from the inside of the barrel, tighten the union nut from the outside.
After the installation is completed, we proceed to the installation of shutoff valves. We select the crane in accordance with the diameter of the fitting. Screwing the valve onto the tie-in shank, hold the union nut with the second key.
At the end of the installation, water is poured into the container and the tightness of the connection is checked. If no leaks are found, the installation can be considered successful.

Now that we know how to attach a crane to a plastic barrel, let's take a closer look at the features of the operation of such structures.

Application features

A plastic container with installed drain fittings is a useful household structure that can be used to meet various household needs.

Among the possible applications, we note the following:

Installations for watering plants are simply indispensable in the countryside and on suburban area. Often, due to the lack of a connection to the water supply, well water is used for irrigation, which accumulates in barrels. Again, a special container of 200 liters can be placed under the drain and thus collect rainwater.
An important condition for the effective operation of irrigation systems assembled on the basis of barrels with a tap is the difference in levels. In other words, the barrel should be located an order of magnitude higher than the end of the watering hose will be.
In this case, the movement of water by gravity and, as a result, the creation of pressure will be ensured. To do this, the container is installed under the roof overhang on a pedestal about 1.5 meters high. A drainpipe is inserted into the barrel, through which it will drain rainwater. The crane is installed at the bottom of the walls of the barrel or at the bottom.
The summer shower is arranged in a similar way. The container is mounted on a frame that acts as a booth.
A tie-in is made at the bottom of the barrel and a fitting is installed on which a tap and a strainer are attached. The second insert is made in the upper part of the container. A flexible hose is attached to this fitting, through which water will be supplied from a water main or from a well using a submersible pump.
The logic of this design is that the filled container heats up under the sun for a certain time, transferring heat to the water. Thus, having collected a container in the morning, in the afternoon you can use water heated to about + 50 ° C.

Conclusion

Now we know how to screw the tap into a plastic barrel and how to use the result for its intended purpose. It remains to purchase the necessary fittings and do simple installation work.

Are there any questions that need clarification? In that case more useful information can be found by watching the video in this article.