Design

How to stick a vinyl sticker on a car with your own hands. We decorate nails in various ways What can you stick vinyl stickers on

Instructions for SMALL stickers!!!
Step 1. First, check the surface: it should be clean, dry, smooth. To do this, gently wipe the surface to be glued with a dry, clean cloth. Check that there are no threads or fluff left that could damage the adhesive surface of the sticker. Before applying the sticker, we recommend washing plastic, glass and metal surfaces with detergent and then wiping them dry.

Step 2 Open the sticker. A mounting film is pasted over the application. Smooth all the elements of the sticker to the mounting film well - the mounting film is designed to transfer the sticker, but not for permanent storage, therefore, it is acceptable to leave the decorating film from the mounting film.

Step 3 Peel the backing from the mounting tape and pull it down. Be careful that all elements remain on the mounting film. If some small elements remain on the substrate, they should be immediately pressed against the mounting film. After removing every 10-15 cm of the substrate, smooth the sticker to the surface with a squeegee or plastic card, moving from top to bottom. When the backing is completely removed, smooth the entire surface of the decal with a squeegee or plastic card. Make sure that there are no air bubbles under the application. If the bubbles cannot be smoothed out, then they can be pierced with a thin needle and then smooth this place with a squeegee or a plastic card.

Step 4 Carefully start peeling off the mounting tape. Pull it to the right or left side, and not towards you, make sure that the application remains on the surface, and not on the mounting film. If unevenness occurs on the sticker, they can be pressed to the surface by heating the sticker with a hair dryer.

Attention!
Stickers are intended for one-time gluing.

Instructions for BIG stickers!!!
First you need to wash and clean the place where the sticker will be located from chemical contaminants.

1. The temperature in the place where you are going to stick the sticker (indoors or outdoors) must be at least 5 degrees Celsius. Small stickers (for example, on the hood), on flat surfaces, can be glued at lower temperatures.

2. First, decide on the place where you are going to stick the vinyl sticker. Decide where the top corners of the decal will be so that the car decal will adhere evenly. It is advisable to mark the points on the car and on the sticker with something waterproof, so that when gluing the marks can be combined and avoid uneven gluing.

3. Without removing any backing, apply the sticker to the car and see how it lays down and fits the surface. Measure everything so that there are no overlays later.

4. Remove the sticker. Peel off the bottom protective paper layer from the image with the mounting film.

5. Pre-treat the entire surface where the sticker is attached to the car, and the sticker itself (on the adhesive side) with water from a sprayer. This will make it possible, after you attach the sticker to the car, to move it, adjusting the placement and easily expel all air bubbles from under the film. DO NOT WET THE PAPER BACKING OF THE STICKER WITH WATER, OR THERE WILL BE PROBLEMS WITH THE SEPARATION OF THE STICKER FROM THE SUBSTRATE!

6. After attaching the sticker to the car, roll it evenly with a rubber spatula or something with a sharp angle, from the middle to the edges. Make sure that the sticker does not bulge, and there are no wrinkles.

Important! If your surface is not smooth, with transitions, do not try to roll the entire sticker at once. Roll on the center of the decal that runs over a flat area, leaving the edges unrolled. Roll the rest later, from the middle of the sticker to the edges, stretching and heating the sticker with a hair dryer, preventing bubbles and wrinkles from forming.
Important! When rolling, if a wrinkle has formed, you can carefully peel back the rolled part and roll it again, heat the sticker with a thermal gun and smooth out the wrinkle.

Beautiful and well-groomed nails distinguish a beautiful and well-groomed girl. With the help of the original design, it is easy to stand out from the crowd and show your uniqueness. At present, a huge number of products are presented on the industry market, with the help of which women's fingers will always be in the spotlight. One such popular option is sliders. Let's take a closer look at their features, as well as how to glue stickers on nails correctly.

What it is

How to apply nail stickers:

Coat your nails with colored gel polish.
Dry well and remove the sticky layer with a lint-free cloth soaked in clinser.
Separate the sticker from the base and carefully stick it on the nail.
Smooth out wrinkles with a bamboo stick.
Cover the design with a finishing top.

3D

These three-dimensional stickers are not flat, but slightly convex. Such sliders can become an original decoration for the entire manicure or highlight only one nail. Embossed 3D stickers are both water-based and adhesive-based. They are quite easy to work with, and in the sock they are not very whimsical. If you fix them correctly and well, then it should not arise with them. They will not cling to clothing or the body.

They are attached in the same way as the previous options. Only such stickers do not need to be smoothed. One of the disadvantages of such voluminous stickers is the difficulty of removing them. You need a special nail polish remover, tweezers or a scraper.

Application methods

But it is not enough to know how to glue stickers on nails correctly. It is important to remember about several ways to apply them. Let's take a closer look at each of them to make your nail design even more perfect.

On uncured varnish

The most reliable way to design a slider is the method when prints are transferred to an uncured layer of varnish. Many nail artists use a special brush to smooth the sticker. Thanks to it, many problems can be avoided: the drawing will lie flat and not tear. The brush tightly fixes the slider without forming unnecessary bubbles, bumps or waves.

This method has a noticeable resistance, because the coating dries along with the slider. Therefore, the bond will be quite strong. Just one finishing top is enough to secure.

on the sticky layer

The most convenient and easy way that many girls adore and put into practice. Stickers are attached to the top layer. The slider must be straightened with a brush or bamboo stick, and then re-secured with another layer of top. Make sure that the size of the sticker does not go beyond the side rollers.

For a finished manicure

A similar method is a real savior for a finished manicure that needs to be updated. If your nails are painted with gel polish, but you suddenly want a change, then this option is for you. You do not need to remove the old coating, you only need to renew it. Sliders need to be fixed on an acid-free primer (ultrabond). This tool does a great job and fixes the stickers on the nails. And you can fix such a design with the same top.

Now you know how to apply nail stickers. The procedure is quite simple, does not require special costs and does not take much time. But after a few minutes, an unusual print will flaunt on your nails, which will attract the attention of everyone around you.

Stickers on glass or car body must be applied according to the technology. There are two such methods - "dry" and "wet". The first one is better to use for small stickers, and the second - for canvases with a large area. As for the question of how to remove stickers from a car, special tools and compounds are used for this - a building hair dryer, gasoline and other means. Which ones - you will find out further by reading the article to the end.

How to stick a sticker on a car

Depending on the material of the sticker, its size, and the place where you plan to stick it, the methods of this process may vary. There are so-called "dry" and "wet" pasting methods. Let's start with the last one. If you plan to glue a large area vinyl film, then for this you will need the following materials:

directly sticker;
detergents for the surface of the car (car shampoos or similar compounds);
soap solution;
stationery knife or scalpel;
plastic spatula;
needle;
(it is best to use alcohol or vodka, it is better not to use solvents, as they can damage the car's paintwork);
building or household hair dryer (preferably building).

Using soapy water and a hair dryer

It is worth paying attention to the environment in which the work is carried out. The temperature in the room must be at least +10°С, the air must be dust-free and there must be no drafts. The next operation takes place in several stages. The first of them involves surface preparation, the second - fitting, the third - application, the fourth is the gluing itself and the elimination of defects. All work is performed according to the following algorithm:

The surface to be pasted must be thoroughly washed, remove grains of dirt, grains of sand and other debris. Any, even the smallest particle that has fallen under the sticker will be visible, which will spoil the appearance of the surface.
Try on the sticker to the surface. If her canvas is large, then it makes sense to glue it in parts. In this case, decide into which parts you need to divide it. In this case, it is necessary to proceed from the considerations that it is necessary to glue flat surfaces first of all, and then convex ones. After that, the joints between them should be processed.
Separate the paper base from the sticker.
Apply a soap solution to the adhesive surface of the sticker, as well as to the surface of the car where you plan to stick it.
Gently apply the sticker to the surface. Soap solution will help you align it in case you didn’t manage to glue it evenly the first time.
Using a rubber spatula, gently smooth it out, starting from the center and out to the edges.
Remove the top protective film from the surface without damaging the auto-sticker and without peeling off the adhesive layer from the main surface.
If an air bubble has formed under the sticker, it is necessary to carefully pierce it with a needle so that the air comes out.
If the film is pasted at the joints of the doors, then it must be cut with a clerical knife.
The final stage consists in heating the surface with a building hair dryer to a temperature of +60...70°C. This is necessary so that the sticker becomes soft, and it is easy to bend it at the joints.

Don't overdo the temperature. Otherwise, the sticker may simply melt.

The first few days (up to about 10) after gluing don't want to wash the car. It takes some time for the glue to dry completely.

directly the sticker that is planned to be pasted;
glass cleaner and rags;
mounting tape;
ruler or tape measure;
scissors;
rubber spatula, plastic card or other object with a flat edge (optional).

Work is carried out according to the following algorithm:

“Dry” gluing method

First of all, you need to thoroughly wash the glass surface where you plan to place the sticker, remove particles of debris and sand.
Next, place the sticker in the planned place and secure it to the upper corners with mounting tape.
Using a ruler or tape measure, align the sticker, check the symmetry. If necessary, move the sticker and reattach with tape at the corners.
Attach a strip of mounting tape in the middle of the sticker vertically. Remove the tape from the top left corner of the sticker.
Lift the left half of the sticker and separate the backing from it (up to the mounting tape). When doing this, make sure that the mounting tape is aligned with the pattern.
Cut off the separated piece of backing and set aside.
Using a spatula or card, begin to carefully stick the sticker, moving from the center to the edges. Make sure that no air bubbles form.
When half of the sticker is pasted, remove the mounting tape from the middle and right corner of the sticker.
Remove the remaining backing. When doing this, make sure that the mounting tape is aligned with the pattern.
Glue the right side of the sticker in the same way. Act carefully and carefully. Make sure there are no air bubbles.
When the entire sticker is installed, remove the mounting film from it. It's best to do it at an angle.

Stickers on the side of the car are installed in the same way. The main thing is to always act carefully and not rush. However, car owners often wonder not only about applying, but also about removing the sticker from the surface of the car, as well as the adhesive residue from it.

How to remove a sticker from a car

Using a hair dryer to remove the sticker

We will analyze in detail how to remove the sticker from the glass of the car or its body. First of all, you need to know that there are different types of stickers, but vinyl ones are the most popular among motorists.

You need to start the story with the features of vinyl stickers. The fact is that they are produced on the basis of vinyl (a chemical compound that is resistant to moisture, temperature extremes, and so on), which has excellent performance properties, durability, strength, and resistance to external influences. Stickers are produced disposable, and their glue is designed for operation within 2-3 years. After that, it polymerizes, and the sticker itself shrinks. In addition, its surface is often covered with cracks, and when you try to tear it off, it breaks off into small pieces.

Another common type of stickers is paper-based. They are cheaper, but not resistant to moisture and temperature extremes. However, they are often used for gluing on the inside of glass.

If your car has a dark tint and the sticker has been on it for a long time, then it is likely that after removal, the tint in its place will be darker than on the rest of the surface.

A popular way to remove a sticker from a car body is to heating it with a hair dryer. At high temperatures, the material becomes soft, and if it is not very cracked, then there is a good chance that it can be removed in one piece. The metal must be heated evenly. As it cools, it is necessary to periodically maintain the temperature. Remember that the higher the temperature of the metal, the less likely it is that adhesive residue will remain on the surface. However, do not overdo it with this, otherwise you may damage the car's paintwork.

How to remove adhesive residue from the surface of the car and glass

Adhesive residues can be removed by first moistening them with alcohol or alcoholic mixtures. Be careful when using different solvents. Read the ingredients beforehand to make sure they won't damage your car's paintwork. In particular, in this case do not use solvents based on acetone, both directly and by acetone itself.

You can also remove after vinyl stickers on a car using:

Comparison of various adhesive removers and adhesives

gasoline;
kerosene;
removal fluids;
silicone solution to remove glue from the body;
paint degreaser.

After using the listed liquids, do not forget to use foam (soap solution) to wash off their remnants. Also, some car owners in such cases remove the remnants of glue with very fine sandpaper (“zero”). However, after that, the problem area will need to be polished with a polishing paste. In stores, you can find a special rubber roller that is put on a drill. It can also be used to effectively remove pre-softened glue.

Results

Sticker film on the car is not particularly difficult. This is especially true for small labels. Almost any car owner can handle this. Another thing is if you want to use vinyl stickers on the car all over the body (for example, “carbon look”). In this case, it is better to seek help from the masters.

Beautiful and well-groomed hands with a bright, or, conversely, discreet manicure, make a good impression on others. If there is no time for the master's artistic work in the salon, you can decorate your nails at home. To do this, you need to master the technique of how to choose stickers for nails and glue them correctly.

The adherence of nail design fans to stickers is explained by the fact that:

Where to buy nail stickers

Stores specializing in the sale of products and accessories for nail bars and beauty salons have a wide range of stickers. Also, sticker sets can be ordered on the Internet, but it will take more time, although it will be much more profitable in terms of price and range of choices.

Classification

Nail stickers (how to glue them and create original versions will be described below) differ in the method of application to the surface of the nail:

On which nails of the fingers to glue stickers, design

Applying nail stickers like a pro is easy. The main thing is to choose the right style that will not seem vulgar. When choosing fingers to apply stickers on, it is important to know the measure and create a tasteful design.

Not guided by the principle "the more the better."

In the presence of large and long nail plates, you can decorate all nails in the “smile” zone.
A short nail plate involves the use of stickers on 1-2 fingers (for example, thumb and ring finger). This is important in order not to overload and weight the nail visually.
Decoration for a special occasion may involve a smart design using rhinestones and voluminous jewelry. In this case, it is also important to observe the measure and be guided by a sense of style. For voluminous jewelry, the location on the ring finger is considered optimal in combination with a suitable coating on other nails.
Color and pictures can be selected according to the season, events, age and personal preferences.

Preparatory stage

The preparatory stage is a set of the following actions:

Application technology for gel polish

After preparing each nail for a manicure with a shellac sticker, the following steps are performed:

After applying the base coat, it is necessary to dry the nails under an ultraviolet lamp.
The next step will be shellac coating and also dry.
The sticker is applied to the nail and the protective layer is removed from it.
After fixing the sticker on the nails, a finisher is applied and dried under the lamp.

Shellac stickers

Stickers on nails, how to glue them on shellac, how to dry them properly - all these aspects are discussed in detail below. The most suitable stickers for shellac coating are water-based stickers. Transfer stickers and photo prints have proven themselves well. An important condition is a flat and smooth surface of the nail plate.

In this case, the sticker will look good.

Nails are pre-treated.
This is followed by a base coat and shellac.
Everything is dried under the lamp.
The resulting sticky layer is removed.
The sticker is applied to the nail, straightened and fixed.
Nails with a sticker are covered with a top.

Such a manicure lasts a long time and reliably.

Self-adhesive water stickers

After the preparatory stage described above, it is necessary to prepare:

You need to do the following:

Try on nail stickers if full coverage is planned.
Apply a base coat of polish to the nail.
Dip the stickers into the water and wait until they are ready to be removed from the protective layer.
Carefully pick up the sticker with tweezers and apply to the nail.
Excess moisture from the sticker is removed with a napkin or cotton pad.
It is important to handle the sticker carefully, straightening and stretching the image over the nail.
Next, a final fixing layer is applied.

Stickers that need to be torn off later

Tear-off stickers are usually a piece of thin foil that covers the entire nail or certain parts of it. For this, a special nail glue is used.

Here is one of the designs:

For such a design, only special nail foil is suitable. You need to be careful with it, as it is very thin and easily torn.

Stickers attached with glue

Stickers on nails (how to glue them without a special adhesive coating on the back) require the use of special manicure glue. With its help, voluminous and heavy jewelry for nails are fixed.

Usually glue is supplied in the kit and it is better to use it.

After the initial treatment of the nail and the application of the base, glue is applied to the nail.
After a few seconds (the exposure time should be indicated in the instructions), decorative elements are applied to the adhesive surface and pressed tightly against the nail.
If necessary, the entire design is covered with a top coat of transparent varnish.

Transfer stickers

It is not difficult to work with products that are transferred to the surface of the nail plate:

Full size water sliders

Sliders are sold in 2 versions:

Ready-made forms for nails
A single sheet from which to cut shapes.

Slider design is suitable for gel polished nail.

To decorate nails with a slider, you need:

Shape the nails, clean them and degrease them.
Cover the nails with gel polish and dry under the lamp.
Soak the sliders in warm water (soak time is indicated in the instructions).
Move the slider aside and remove it from the paper base.
Attach the sticker to the nail and press it with a cotton pad to get rid of excess moisture.
Cover your nails with a final coat of clear polish.

Lace

Sliders with a lace pattern come in 2 types:

For greater effect, a sticker with a lace pattern is selected for a plain base polish.

Easy to paste:

The nail, which has undergone preliminary processing and turning, is covered with a monophonic varnish of any shade.
A fragment of the lace pattern is cut out from the palette and separated from the base.
With gentle movements, a transparent slider is applied to the nail.
The composition is covered with a fixing varnish.

Broken glass

To create the effect of "broken glass" special foil paper is used.

The choice of colors and effects is huge: mother-of-pearl and mirror fragments from pastel to bright and catchy colors will definitely attract the attention of others.

Such a simple and inexpensive way will create the effect of an expensive salon manicure. It is important to remember the thoroughness of execution, since the corners of “broken glass” sticking out in different directions will only spoil the beauty. Additional decorations in the form of sparkles, rhinestones and "eggs" will be inappropriate.

foil products

Foil stickers are shiny or matte pieces of thin foil. Usually.

They are glued with a special glue, which is applied either to the entire nail plate, or to part of it.

The treated nails are covered with glue.
After a certain time, a foil is applied to the area covered with glue.
Unnecessary pieces of foil are carefully sawn off or cut off.
The nail is covered with a final layer of transparent varnish.

3D stickers

3D stickers are distinguished by volumetric details, bulges on the surface. You need to glue them like this:

3D stickers will not interfere with everyday activities, even despite the voluminous design.

Shellac stickers

After preparing the nails for manicure, the application technology will be as follows:

The nails are covered with a base and a layer of shellac.
The surface to be applied is thoroughly dried under the lamp.
The sticky surface is cut off with a buff.
The selected pattern is removed from the palette and applied to the nail. It is important at the same time to ensure that the picture is superimposed evenly and without folds.
After smoothing the sticker, a layer of clear fixative varnish is applied.

Photoprint

When working with photoprint stickers, remember that the use of water is contraindicated.

Gluing them is simple and easy:

A photo print of the desired size is glued onto the prepared nail plates. If the sticker is full size, then the corners and protruding parts are carefully cut off or folded down.
After that, you can carefully file the protruding ends with a nail file.
A transparent fixative is applied on top.

It is necessary to monitor the accuracy of contact and fixation of the sticker on the surface of the nail.

golden stickers

Gold stickers will look great at a gala evening event.

Gluing them is not difficult, but additional practice does not hurt.

Honed and fat-free nails are covered with a colorless base varnish.
After the base has dried, the gold foil is removed from the base and applied to the nail in an even layer.
With a cotton or orange stick, the foil is distributed over the entire surface. The foil is quite thin, and therefore you should not rush, so as not to break the fragment.
The protruding corners of the film can be cut off with a file, moving from top to bottom along the edge of the nail.
A fixing layer of varnish is applied on top.

Velvet stickers

Velvet stickers are considered another popular novelty. Usually they are patterns with a short pile.

These stickers are attached to a transparent film.

After pre-treatment of the nails, a base is applied to the surface of the nails, transparent or colored, depending on individual preferences.
The velvet pattern is removed from the substrate and applied with the sticky side to the nail.
A finisher is not needed in this case, as it can destroy the velvet effect.

Velvet stickers are quite durable, and therefore, according to the manufacturers, they will stay on the nails for more than 15 days.

Reasons for peeling sliders

Important conditions for maintaining a manicure with sliders that professional nail art masters observe are:

High quality material.
Compliance with all rules when applying sliders.

If the master decided to save money and used low quality sliders, they will begin to peel off already in 3-4 days. It is important to remember that before fixing the slider, you need to dry the lower layers of the base varnish well.

The sticker should be carefully pressed and smoothed over the surface of the nail. If the work is not done carefully, then the stickers will begin to peel off the nail after a very short period of time.

The picture is not bright enough or almost invisible

This happens if the basic conditions are not met:

Chips in the finish

Defects of this type appear for several reasons:

Poorly dried base and finisher layers.
Too thick coating.
When sealing the tips, too much top is applied. As a result, cracks that have arisen due to the critical load.
Uncured surface of the decal where the top has been applied.

Pattern Peel Off With Top Coat

To save a manicure for a long time, you must remember that even the highest quality material will not withstand prolonged contact with water. Therefore, experienced users are advised to wash dishes, windows and floors with gloves. Also, the durability of a manicure can be harmed by the lack of a transparent top, designed to protect the sticker from external factors.

The sticker does not fully adhere to the nail plate

The sticker may bubble if:

It was glued carelessly, and air got under it.
The adhesive surface of the slider is processed unevenly.
Poor quality components used.

In order to know how to glue stickers on nails, it is not necessary to be a nail art specialist. You can make a beautiful manicure at home, you just need to practice a little.

Article formatting: Mila Fridan

Video about stickers in manicure

How to stick stickers:

In the general image of a woman, manicure plays an important role, and in it you can express your creative personality, endlessly changing color combinations, choosing patterns and designs. However, not everyone has enough time or skills to paint nails on their own, and then specially prepared stickers come to the rescue. Depending on their type, they can become both a single accent and a full-fledged manicure.

How to apply water stickers on nails?

To date, the consumer is offered 2 types of nail stickers: water-based, designed for slider design and appeared quite a long time ago, and stickers with photo design. Each of the options has its own characteristics in application and wear, which you should definitely consider if you want to get a high-quality and durable manicure. However, using any of the sticker types is quite simple and aimed at the consumer who does not have high-end nail art skills.

Water stickers for slider design are a fairly well-known product designed to create accents on individual nails. A thin film (often transparent) laid on white cardboard can have both a small pattern and spaced along the entire length and width of the intended nail. Due to this, it is convenient to fix it even on children's nails, especially since such a design is much safer than drawings with acrylic paints.

To remove the film from the cardboard, it is enough just to slightly moisten it with water - for this, the selected area is cut off and for 2-3 seconds. is placed in a container with cold water, after which it is immediately removed, deprived of excess moisture with a lint-free cloth and applied to the nail. Trying to pull the film off the cardboard with your hands is fraught with its rupture.

Due to the fact that most water stickers have a translucent base, in the manicure procedure it is important to choose the shade of the base varnish: it should not argue with the color scheme of the pattern applied to the film, and should not merge with it. Masters recommend choosing either contrasting tones, or the most neutral ones - jelly beige-pink, flesh. On a white substrate, the picture will look brighter, but only if it is not itself made in white.

As for how to stick stickers of this type on nails, there are no particular difficulties in this algorithm: the main thing is to use a base and top coat. The substrate is necessary for the primary adhesion of the sticker and the adhesive base, while the top layer is for sealing the design. It is not necessary to wait for the base coat to dry: the varnish should remain slightly sticky, but not smeared with a light touch.

When working with gel, it is also worth laying the sticker without removing the sticky layer. It should lie on acrylic after partial polymerization of the material, and it will not be possible to move it - there is a high probability of the sticker dissolving. It is recommended to fix it with gel (1 layer) or classic varnish (2 layers). A layer of transparent acrylic cannot be placed on top of the sticker.

It is recommended to straighten the sticker with a wooden stick, laying it flat and moving it from the center to the edges, thus expelling all air bubbles. The duration of wearing water stickers rarely exceeds 7 days, but among their advantages, professionals note resistance to deformation and tearing.

How to glue stickers on gel polish?

It is recommended to use stickers with photo design under gel polish. In this situation, they act as the main color layer, since such stickers are a denser plate that has the shape of nails of various widths. As accents, they are no longer used - this is a full-fledged manicure, which is very difficult to fix with ordinary varnish - it has a thinner coating and a low degree of protection, and the latter plays an important role in manicure with photo design.

The main problem is that this kind of stickers are very afraid of water, and contact with it in everyday life is inevitable. A simple varnish begins to chip off already on the 2-3rd day of wearing, as a result of which water enters the lower layers of the manicure. Gel polish, with the right technology, will not allow this to happen.

Before placing the stickers on the nails, they need to be adjusted to your individual width. The length can be removed already in the process. The base coat of gel polish is thinly applied in 1 layer, dried for 60 seconds (UV lamp), and the sticky layer is not removed from it. The sticker must be placed, practically without indenting the cuticle, smoothed out with a wooden stick, also working from the center to the edge.

To make it easier to remove the sticker from its backing, it is recommended to use tweezers. If the length of the sticker turned out to be more than necessary, the rest is folded over the free edge, pressed and filed with a 100/120 grit file. At the same time, the file must be held clearly perpendicular to the end, and in no case be tilted at an angle. The final layer of gel polish is applied denser than the base, and with the obligatory careful sealing of the ends. It dries in 120 seconds if the work is done with a UV lamp.

Before using stickers, if they are located on the entire nail plate, a classic manicure is necessarily performed, in which a lot of attention is paid to the removal of pterygium. This is especially true for stickers with a photo design, which are often already a full-fledged manicure and fit in such a way that they consistently affect the bare nail. The elimination of pterygium provides an even nail plate, adhesion to which will be as true as possible. And an accidental hit of a foreign element under the edge of the sticker will lead to the appearance of "pockets", as in extensions, and will reduce the durability of the manicure to "no".
If the sticker is not a small design, but should cover the entire nail, place it so that there is a 1-2 mm indent from the cuticle and side ridges: this will guarantee that there will be no peeling, and the sticker will not leave the nails after a few hours . Moreover, if you are afraid that in the end you will get a manicure that looks like a week or more, because of such a distance, just before applying the sticker, move the cuticle and side rollers as far as possible with a pusher or a wooden stick. After 20-30 min. they will return to their place and close the indent created.

Manicure with stickers of various types: options

In manicure, nail stickers are quite self-sufficient and practically do not tolerate other design elements next to them: fimo, modeling, rhinestones. Depending on which pattern you have chosen, the base color of the varnish is selected, if it is visible at all from under the sticker. But the stickers with a 3D design look the most spectacular, designed like an "aquarium": sealed in a dense layer of transparent gel or acrylic. In the case of the latter, it is important to remember that, unlike varnish, it is not stretched over the nail, but is trampled: this will prevent the sticker from deforming.

The easiest way is to come up with and reproduce a manicure with stickers that have a photo design: they do not require additional tricks, in most cases being a complete idea. But with water stickers, you can go for experiments: in particular, this applies to accent stickers. For example, small white flowers, placed on the ring finger, deserve the addition of stems and leaves, which are displayed with acrylic paint of the appropriate color and a thin nylon brush.

Simple black and white stickers in the form of geometric shapes, stars, hearts and other elements will become individual if the space inside them is filled with colored varnish, broths, sparkles, acrylic paint. But do not forget to obligatorily cover such a design with a dense layer of top: otherwise, all the decorative little things will quickly fly off the nail and pull the sticker along with them.

Lace, which does not diminish its popularity, being wide, can turn a simple French manicure into an elegant and unusual one. It is enough just to place the lace strip on the overgrown edge of the nail and bend it, if necessary, along the smile line. Excess length is eliminated with a file, the sticker is sealed with varnish.

Nail stickers are a salvation for girls who want to diversify their manicure, but do not have the skill to paint or other complex designs. Working with them is simple and easy, the result depends only on the imagination of the author of the manicure, and the durability, with the right technology, will be equal to the durability of the varnish applied under them.